Read Sony AVD-K700P / HT-V700DP Service Manual online
2
AVD-K700P
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
AUDIO POWER SPECIFICATION
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 6 ohm loads, both channels
driven, from 120 - 20,000 Hz; rated
90 watts per channel minimum RMS
power, with no more than 10 % total
harmonic distortion from 250 milli
watts to rated output (USA model
only).
HARMONIC DISTORTION:
With 6 ohm loads, both channels
driven, from 120 - 20,000 Hz; rated
90 watts per channel minimum RMS
power, with no more than 10 % total
harmonic distortion from 250 milli
watts to rated output (USA model
only).
Amplifier
Stereo mode
90 W + 90 W (6
Ω
at 1 kHz, THD
10 %)
Surround mode
Front: 90 W/ch (6
Ω
at 1 kHz, THD
10 %)
Center*: 90 W (6
Center*: 90 W (6
Ω
at 1 kHz, THD
10 %)
Surround*: 90 W/ch (6
Surround*: 90 W/ch (6
Ω
at 1 kHz,
THD 10 %)
Subwoofer*: 150 W (4
Subwoofer*: 150 W (4
Ω
at 30 Hz,
THD 10 %)
*Depending on the sound mode settings
and the source, there may be no sound
output.
and the source, there may be no sound
output.
Inputs
VIDEO 1, VIDEO 2, OPTICAL IN
Design and specifications are subject to change without notice.
FM Tuner
87.5 - 108.0 MHz
10.7 MHz
10.7 MHz
AM Tuner
530 - 1,720 kHz
450 kHz
450 kHz
Tuning Range
Intermediate Frequency
Tuning Range
Intermediate Frequency
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
other than those specified herein may result in hazardous radiation
exposure.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
Click on the first or last page to see other AVD-K700P / HT-V700DP service manuals if exist.