Read Sony AIR-SA50R Service Manual online
AIR-SA50R
6
SECTION 3
TEST MODE
COLD RESET
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. While touching the [
N
] sensor, press two buttons [SLEEP/
BRIGHT] and [
?/1
] simultaneously.
3. The message “RESET” appears on the liquid crystal display,
then turn the power off.
PANEL TEST MODE
Procedure:
1. In the standby state, while touching the [PRESET +] sensor,
Procedure:
1. In the standby state, while touching the [PRESET +] sensor,
press two buttons [SLEEP/BRIGHT] and [
?/1
] simultane-
ously.
2. When the panel test mode is activated, all segments of the liq-
uid crystal display are lighted up.
3. In the state of step 2, press the [SLEEP/BRIGHT] button, and
the version of the micro controller and destination are dis-
played on the liquid crystal display.
played on the liquid crystal display.
4. In the state of step 2, press the [S-AIR/AUDIO IN] button,
the message “Key 0” is displayed on the liquid crystal display.
When all buttons (All buttons including [
When all buttons (All buttons including [
?/1
] and [PAIRING]
(button on back panel side)) are pressed and all sensors are
touched, the message “Key 16 OK” is displayed on the liquid
crystal display.
touched, the message “Key 16 OK” is displayed on the liquid
crystal display.
5. To release from this mode, while touching the [PRESET +]
sensor, press the two buttons [SLEEP/BRIGHT] and [
?/1
] si-
multaneously.
REMOTE DISABLE MODE
Procedure:
1. In the standby state, while pressing the [S-AIR CH +] button,
Procedure:
1. In the standby state, while pressing the [S-AIR CH +] button,
press the [
?/1
] button to turn the power on.
2. The message “REMOTE ON” or “REMOTE OFF” appears
on the liquid crystal display, and on/off of the remote control
changes.
changes.
TOUCH PANEL BEEEP SOUND ON/OFF MODE
Procedure:
1. In the standby state, while pressing the [S-AIR/AUDIO IN]
Procedure:
1. In the standby state, while pressing the [S-AIR/AUDIO IN]
button, press the [
?/1
] button to turn the power on.
2. The message “BEEP ON” or “BEEP OFF” appears on the
liquid crystal display, and on/off of the beep sound when the
touch panel is operated changes.
touch panel is operated changes.
S-AIR TEST MODE
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. While touching the [
x
] sensor, press two buttons [S-AIR/
AUDIO IN] and [PAIRING] (back panel side) simultaneously.
3. The message “I2C” appears on the liquid crystal display and
enter the S-AIR test mode.
4. Touch the [PRESET +] sensor to select the “I2C”, and touch
the [ENTER] sensor.
The message “OK” or “NG” appears on the liquid crystal dis-
play and the connection of the I2C line between DARR and
micro controller can be confi rmed.
play and the connection of the I2C line between DARR and
micro controller can be confi rmed.
“OK” : Connection OK.
“NG” : Connection NG.
Touch the [ENTER] sensor, return to item selection screen.
5. Touch the [PRESET +] sensor to select the “QUALITY”, and
touch the [ENTER] sensor.
The quality of the communication is displayed on the liquid
crystal display.
crystal display.
Touch the [ENTER] sensor, return to item selection screen.
6. Touch the [PRESET +] sensor to select the “POWER”, and
touch the [ENTER] sensor.
The output power is displayed on the liquid crystal display. In
this state, whenever the [PRESET +] and [PRESET –] sensors
are touched, the output power can be changed.
this state, whenever the [PRESET +] and [PRESET –] sensors
are touched, the output power can be changed.
Touch the [ENTER] sensor, return to item selection screen.
7. Touch the [PRESET +] sensor to select the “VER.CHECK”,
and touch the [ENTER] sensor.
The microcomputer version last updated date of the S-AIR de-
vice connected with this set is displayed on the liquid crystal
display.
vice connected with this set is displayed on the liquid crystal
display.
Touch the [ENTER] sensor, return to item selection screen.
8. Touch the [PRESET +] sensor to select the “DARR”, and
touch the [ENTER] sensor.
The settings of DARR are displayed on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the displayed setting of DARR can be changed.
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the displayed setting of DARR can be changed.
“CO XXXX” : Connect code display.
“ADR XX” : Address display.
Touch the [ENTER] sensor, return to item selection screen.
9. Touch the [PRESET +] sensor to select the “ANT SET”, and
touch the [ENTER] sensor.
The setting of antenna transceiving is displayed on the liquid
crystal display. Whenever the [PRESET +] and [PRESET –]
sensors are touched, the setting of antenna transceiving can be
changed.
crystal display. Whenever the [PRESET +] and [PRESET –]
sensors are touched, the setting of antenna transceiving can be
changed.
Touch the [ENTER] sensor, return to item selection screen.
10. Touch the [PRESET +] sensor to select the “ANT MON”, and
touch the [ENTER] sensor.
The antenna under use is displayed on the liquid crystal dis-
play.
play.
Touch the [ENTER] sensor, return to item selection screen.
11. Touch the [PRESET +] sensor to select the “REC”, and touch
the [ENTER] sensor.
Whether the audio source that has been reproduced can be re-
corded is displayed on the liquid crystal display.
corded is displayed on the liquid crystal display.
Touch the [ENTER] sensor, return to item selection screen.
12. Touch the [PRESET +] sensor to select the “DEMO”, and
touch the [ENTER] sensor.
The message “ON” or “OFF” appears on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the on/off can be changed.
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the on/off can be changed.
“ON” : Demo mode (Mode for demonstration at shops).
“OFF” : Normal mode.
Touch the [ENTER] sensor, return to item selection screen.
13. Touch the [PRESET +] sensor to select the “RF CHG”, and
touch the [ENTER] sensor.
The message “ON” or “OFF” appears on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the on/off can be changed.
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the on/off can be changed.
“ON” : The RF CHG function of DARR is on.
“OFF” : The RF CHG function of DARR is off.
Touch the [ENTER] sensor, return to item selection screen.
14. Touch the [PRESET +] sensor to select the “NA SEND”, and
touch the [ENTER] sensor.
The message “ON” or “OFF” appears on the liquid crystal dis-
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the on/off can be changed.
play. Whenever the [PRESET +] and [PRESET –] sensors are
touched, the on/off can be changed.
“ON” : NACK is transmitted at the Bad_Sync.
“OFF” : NACK is not transmitted at the Bad_Sync.
Touch the [ENTER] sensor, return to item selection screen.
15. To release from this mode, press the [
?/1
] button. The setting
is maintained until turning off power.
Click on the first or last page to see other AIR-SA50R service manuals if exist.