Read Sony AIR-SA17TI Service Manual online
AIR-SA17Ti
AIR-SA17Ti
7
7
3-1-6. Channel pipe setting
This mode is channel pipe is setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is channel pipe is setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “CH1 PIPE” (or “CH2 PIPE”, “CH3 PIPE”,
“CH4 PIPE”).
“CH4 PIPE”).
3. Press the [ENTER] button, the messages “CH* - CH#” is dis-
played on the fl uorescent indicator tube.
*: channel number of selected step 2
#: number of channel pipe
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select channel pipe setting.
5. Press the [ENTER] button, return to S-AIR test mode each
item.
3-1-7. NAMG setting
This mode is change of NAMG setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is change of NAMG setting.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “NAMG”.
3. Press the [ENTER] button the messages “*** SET” is dis-
played on the fl uorescent indicator tube.
***: 107 to 117 or AUTO
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the NAMG setting value.
5. Press the [ENTER] button, return to S-AIR test mode each
item.
(This mode setting value is buck up even if it turns off power)
3-1-8. DEMO setting
This mode is radio wave does setting change to improve connec-
tion by batch processing in shop etc. when connection does not go
well badly.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
This mode is radio wave does setting change to improve connec-
tion by batch processing in shop etc. when connection does not go
well badly.
Procedure:
1. Enter the S-AIR test mode.
2. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select “DEMO”.
3. Press the [ENTER] button the messages “ON” or “OFF” is
displayed on the fl uorescent indicator tube.
4. Press the [TUNING/SELECT +]/[TUNING/SELECT –] but-
tons to select the “ON” or “OFF”.
ON: batch processing on
OFF: batch processing off (default)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
4. COLD RESET
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. Press the [SYSTEM MENU] button, and press the [TUNING/
Procedure:
1. The [POWER] switch is set [ON] to turn the main power on.
2. Press the [SYSTEM MENU] button, and press the [TUNING/
SELECT +] button to select “RESET”.
3. Press the [ENTER] button twice.
4. The cold reset is executed.
4. The cold reset is executed.
SECTION 4
ELECTRICAL CHECK
FM TUNE LEVEL CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and tune A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C signals.
When the selected station signal is received in good condition,
“TUNED” is displayed.
“TUNED” is displayed.
Click on the first or last page to see other AIR-SA17TI service manuals if exist.