LC-60LE651KMK2 - Sharp TV Service Manual (repair manual)

COLOUR TELEVISION

Wi-Fi  & 3D Ready / DVB-T / T2 / C / S / S2  PAL

 

B/G, I 

/ SECAM

 B/G, D/K, L/L’ 

SYSTEM COLOUR TELEVISION

In the interests of user safety (required by safety 
regulations in some countries) the set should be re-
stored to its original condition and only parts identical 
to those specifi ed should be used.

CONTENTS

ELECTRICAL SPECIFICATIONS ........................................................................................  2
IMPORTANT SERVICE SAFETY PRECAUTIONS .........................................................................   3
OPERATION MANUAL ....................................................................................................................   6
DIMENSIONS .................................................................................................................... 22
REMOVING OF MAJOR PARTS .....................................................................................................  23
SERVICE ADJUSTMENTS .............................................................................................................  27
PUBLIC MODE ....................................................................................................................................    38
SOFTWARE UPGRADING .............................................................................................................  42
MAJOR ICs INFORMATION .....................................................................................................  43
BLOCK DIAGRAMS .....................................................................................................................  59
SCHEMATIC DIAGRAMS .......................................................................................................  62
PRINTED WIRING BOARDS .........................................................................................................  101
REPLACEMENT PARTS LIST .......................................................................................................  111
CABINET AND MECHANICAL PARTS ............................................................................................  121
PACKING OF THE SET .......................................................................................................................  123

                       Issued: 

10

th 

Sept 2014

SE0060LE651MK

LCD Panel (LED TV)

60”/ 152cm BLACK TFT

Resolution

6.220.800 dots (1.920 x 1.080 pixels)

Video Colour System

PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60

TV 
Func-
tions

TV Standard

Analogue

CCIR (B/G, I, D/K, L/L’)

Digital

DVB-T (2K/8K OFDM)(H.264), DVB-C, DVB-T2(LE651 only), DVB-S/S2 (LE652 only) 

Receiving 
Channel

VHF/UHF

E2–E69 ch, F2–F10 ch, I21–I69 ch, IR A–IR J ch (Digital: IR A ch–E69 ch)

CATV

Hyper-band, S1–S41 ch

TV-Tuning System

Auto Preset 999 ch: non-Nordic / 9999 ch: Nordic (ATV: 99 ch), Auto Label, Auto Sort

STEREO / BILINGUAL

NICAM/A2

Viewing angles

H: 176°, V: 176°

Audio Ampli¿ er

15 W + 15 W (Music power)

Speaker

(96 mm x 30mm) x 2

Terminals

TV Antenna

VHF/UHF

UHF/VHF 75 Ÿ Din type (Analogue & Digital)

Satellite (652 

series only)

75 Ÿ F type (DVB-S/S2)

SERVICE

Ø 3.5 mm jack

SCART

SCART (AV input, RGB input, TV output, Y/C input)

PC INPUT

VGA  (D-Sub 15pin), Ø 3.5 mm jack (shared with HDMI)

COMPONENTS

COMPONENT IN: Y/PB(CB)/PR(CR), RCA (AUDIO R/L)

HDMI1

HDMI, Ø 3.5 mm jack (shared with PC INPUT), ARC, 3D.

HDMI2

HDMI, Ø 3.5 mm jack (shared with PC INPUT), 3D.

HDMI3 

HDMI, Ø 3.5 mm jack (shared with PC INPUT), 3D.

HDMI4 

HDMI, Ø 3.5 mm jack (shared with PC INPUT), 3D.

USB 1

USB 2.0 HOST (A Type) 

USB 2 

USB 2.0 HOST (A type)

USB 3  (WIFI) 

USB 2.0 HOST (A type) (Wi-Fi use only)

ETHERNET (10/100)

Network connector

AV

RCA connector (AV input)

S/PDIF OUT

RCA S/PDIF digital audio output.

C. I. (Common Interface)

EN50221, R206001, CI+ speci¿ cation

Headphones

Ø 3.5 mm jack (Audio output)

OSD language

Czech, Danish, Dutch, English, Estonian, Finnish, French, German, Greek, Hungarian, Italian, 
Latvian, Lithuanian, Norwegian, Polish, Portuguese, Russian, Slovak, Slovene, Spanish, 
Swedish, Turkish, Ukrainian, Byelorussian, Romanian, Croatian, Serbian.

Power Requirement

AC 220–240 V, 50 Hz

Power Consumption (IEC62087 Method)

175W 
(0.24W Stby)

Weight

24.3Kg (Without stand) 
27,3Kg (With stand)

Operating Temperature

0 °C to +40 °C

TO EXPOSED
METAL PARTS

CONNECT TO
KNOWN EARTH
GROUND

DVM

AC SCALE

1.5k ohm

10W

0.15 μF

TEST PROBE

Many electrical and mechanical parts in LCD television have special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily 
increased by using replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are identifi ed in this manual; electrical components 
having such features are identifi ed by    “    “.

For continued protection, replacement parts must be identical to those used in the original circuit.
The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended 
replacement parts shown in this service manual, may create shock, fi re or other hazards.

1. For continued safety, no modifi cation of any circuit should be attempted.
2. Disconnect AC power before servicing.

Before returning the receiver to the user, perform the following safety checks:
1. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the 
chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and 
compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc.
3. To be sure that no shock hazard exists, check for leakage current in the following manner. 

•

 Plug the AC cord directly into a 220~240 volt AC outlet. (Do not use an isolation transformer for this test).

•Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15μF capacitor in series with all exposed metal 
cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.

•A true RMS reading multimeter should be used for this test, especially where the equipment uses a switch mode 
power supply which may result in very non-sinusoidal leakage current.
•Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, 
screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.

All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must 
be used only for the purpose of completing these checks.)
Any reading of 1.05V peak (this corresponds to 0.7 mA. peak AC.) or more is excessive and indicates a potential shock 
hazard which must be corrected before returning the monitor to the owner.

!

  CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF
  FIRE REPLACE ONLY WITH SAME TYPE  F101 (T4 AH / 250V)

Indicates lead-free solder of tin, silver and copper.

“ALL  PWB” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the 
PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:

When fi xing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead 
wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you to 
use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our 
service station or service branch in your area.

As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder by 
40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended 
period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be 
exceeded, remove the bit from the PWB as soon as you confi rm the steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and 
off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every 
use of it.
When the tip of the soldering bit is blackened during use, fi le it with steel wool or fi ne sandpaper.

Be careful when replacing parts with polarity indication on the PWB silk.

Lead-free wire solder for servicing.

Indicates lead-free solder of tin, silver and nickel.

Sn-Ag-Ni