Read Sharp LC-50LE761K Service Manual online
10
LC-42/50LE762
LC-42/50LE761
LC-42/50LE760
English - 7 -
Package Contents
TV
Remote Control
LED TV
Batteries: 2 X AAA
Quick Guide
1 X Video & Audio Connection
Cable
4 x 3D Glasses
Nero media home CD
Note: You should check the accessories after purchasing.
Make sure that each accessory is included.
As the manufacturer’s specification supports
communication on cable lengths shall be smaller
than 3m.
TV Control button & Operation
1. Standby / On button
2. TV/AV button
3. Programme Up/Down buttons
4. Volume Up/Down buttons
2. TV/AV button
3. Programme Up/Down buttons
4. Volume Up/Down buttons
Note: Press Volume Up/Down buttons at the same to view
main menu and use Prpgramme Up/Down buttons to navigate
and Volume Up/Down buttons to change value.
, switch is used for turning the TV on or off.
The position of the control buttons and power switch
may differ depending on the model.
Connect Power
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
Antenna/Cable/Satellite Connection
Connect the aerial or cable TV plug to the AERIAL
INPUT (ANT.) or satellite lead to the SATELLITE
INPUT(LNB) located on the rear side of the TV.
“Satellite is only available in 762 series”.
Rear side of the TV:
Rear side of the TV:
SATELLITE
AERIAL
CABLE
Note: Satellite support is depending on the model.
(only available in LC-42LE762E / LC-42LE762EN /
LC-50LE762E / LC-50LE762EN series)
Installing The Batteries Into The
Remote
• Remove the back cover to reveal the battery
compartment.
• Insert two size AAA batteries. Note the correct
polarity(+ or -). Do not mix old and new batteries.
Replace only with same or equivalent type.
• Place the cover back on.
Angle of the remote control unit
Use the remote control unit by pointing it towards the
remote control sensor.
Objects between the remote control unit and sensor
Objects between the remote control unit and sensor
may prevent proper operation.
Cautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit
to liquids, and do not place in an area with high
humidity.
English - 8 -
• Do not install or place the remote control unit under
direct sunlight. The heat may cause deformation
of the unit.
• The remote control unit may not work properly if
the remote control sensor of the TV is under direct
sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote
control unit closer to the remote control sensor.
Switching On/Off
To Switch the TV On
Connect the power cord to the mains socket. Switch
the “
” button on the TV to position “|” so the TV
will switch to standby mode. Then the standby LED
lights up.
To switch on the TV from standby mode either:
• Press the “
To switch on the TV from standby mode either:
• Press the “
” button,
P+ / P- or a numeric button
on the remote control.
• Press the “
” or
P/CH+/- button on the TV.
The TV will then switch on.
To Switch the TV to Standby
To switch the TV to low power standby press the “
”
button on the remote control or on the TV.
To Switch the TV Off
Switch the “
” button on bottom of the TV to
position 2 as illustrated -
, to isolate the TV from
the mains, the LED will go out.
English - 8 -
• Do not install or place the remote control unit under
direct sunlight. The heat may cause deformation
of the unit.
• The remote control unit may not work properly if
the remote control sensor of the TV is under direct
sunlight or strong lighting. In such cases, change the
angle of the lighting or the TV, or operate the remote
control unit closer to the remote control sensor.
Switching On/Off
To Switch the TV On
Connect the power cord to the mains socket. Switch
the “
” button on the TV to position “|” so the TV
will switch to standby mode. Then the standby LED
lights up.
To switch on the TV from standby mode either:
• Press the “ ” button,
To switch on the TV from standby mode either:
• Press the “ ” button,
P+ / P- or a numeric button
on the remote control.
• Press the “ ” or
P/CH+/- button on the TV.
The TV will then switch on.
To Switch the TV to Standby
To switch the TV to low power standby press the “ ”
button on the remote control or on the TV.
To Switch the TV Off
Switch the “
” button on bottom of the TV to
position 2 as illustrated -
, to isolate the TV from
the mains, the LED will go out.
OPERATION MANUAL - Continued
Click on the first or last page to see other LC-50LE761K service manuals if exist.