Read Sharp LC-42AD5E (serv.man10) User Guide / Operation Manual online
15
Setup menu
Menu operations
MENU
[Setup]
Setup
Option
Child Lock
Auto Installation
Programme Setup
Position
WSS
4:3 Mode
[Panorama]
[On]
[Off (0V)]
Supply Voltage
[English]
Language
Power Management
Menu Operation: A (page 12)
When set, the TV will automatically enter the standby mode.
When set, the TV will automatically enter the standby mode.
Off:
• No power management
• Factory preset value.
• Factory preset value.
Mode1: • If there is no signal input for 8 minutes, the TV
enters the standby mode.
• Even if you start using the PC and the signal
inputs again, the TV stays in standby mode.
• The TV turns on again by pressing a on the
TV or B on the remote control unit. (See page
8.)
8.)
Mode2: • If there is no signal input for 8 seconds, the
TV enters the standby mode.
• When you start using the PC and the signal
inputs again, the TV turns on.
• The TV turns on again by pressing a on the TV
or B on the remote control unit. (See page 8.)
PC only
Auto Installation
You can run Auto Installation again, even after setting
up the preset channels.
up the preset channels.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Auto Installation”, and then
press OK.
If you have already set the PIN under “Child Lock”,
enter it here.
press OK.
If you have already set the PIN under “Child Lock”,
enter it here.
• See page 17 for setting PIN.
4
Press c/d to select “Yes”, and then press OK.
5
You can set language and country the same as in
the initial auto installation. Follow steps 1 and 2
on page 8.
the initial auto installation. Follow steps 1 and 2
on page 8.
TV only
Power Control menu
No Signal Off
Menu Operation: A (page 12)
When set to “Enable” the TV will automatically enter the
standby mode if there is no signal input for 15 minutes.
When set to “Enable” the TV will automatically enter the
standby mode if there is no signal input for 15 minutes.
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
NOTE
• When a TV programme finishes, this function may not
operate.
• This function is not available in DTV mode.
MENU
[Power Control]
Audio
Power Control
No Signal Off
No Operation Off
[Disable]
[Disable]
TV/AV only
No Operation Off
Menu Operation: A (page 12)
When set to “Enable” the TV will automatically enter the
standby mode if no operations are performed for 3 hours.
standby mode if no operations are performed for 3 hours.
• Five minutes before the TV enters standby mode, the
remaining time displays every minute.
TV/DTV/AV only
Programme Setup
This section describes how to set up analogue TV
channels manually.
channels manually.
Auto Search
You can automatically search for and download TV
channels by performing the procedure below. This is
the same function as from programme auto search to
preset download in Auto Installation.
channels by performing the procedure below. This is
the same function as from programme auto search to
preset download in Auto Installation.
1
Repeat steps 1 to 4 in Programme Setup.
2
Press c/d to select “Yes”, and then press OK.
1 Programme auto search
2 Auto labelling
3 Auto sorting
4 Preset download
2 Auto labelling
3 Auto sorting
4 Preset download
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Programme Setup”, and
then press OK.
If you have already set the PIN under “Child Lock”,
enter it here.
then press OK.
If you have already set the PIN under “Child Lock”,
enter it here.
• See page 17 for setting PIN.
4
Press a/b to select “Auto Search”, “Manual
Adjust”, “Sort” or “Erase Programme”, and then
press OK.
Adjust”, “Sort” or “Erase Programme”, and then
press OK.
Auto Search
Manual Adjust
Sort
Erase Programme
No
Yes
TV only
Item
LC-AD5E_GB_b
07.3.15, 5:05 AM
15
Click on the first or last page to see other LC-42AD5E (serv.man10) service manuals if exist.