Read Sharp LC-32LE351K (serv.man2) Service Manual online
12
LC-39LE351
LC-32LE351
Operation Manual (Continued)
English - 11 -
Using a Conditional Access Module
IMPORTANT: Insert or remove the CI module only when
the TV is SWITCHED OFF.
In order to watch certain digital channels, a conditional
access module (CAM) can be necessary. This module
must be inserted in the CI slot of your TV.
1. Obtain the Conditional Access Module (CAM) and the
1. Obtain the Conditional Access Module (CAM) and the
viewing card by subscribing to a pay channel company,
then insert those to the TV using the following procedure.
2. Insert the CAM and then the viewing card to the
2. Insert the CAM and then the viewing card to the
slot that is located in the terminal cover at the rear
side of the TV.
3. The CAM should be correctly inserted, it is
3. The CAM should be correctly inserted, it is
impossible to insert fully if reversed. The CAM or
the TV terminal may be damaged if the CAM is
forcefully inserted.
4. Connect the TV to the mains supply, switch on
4. Connect the TV to the mains supply, switch on
and then wait for few moments until the card is
activated.
5. When no module is inserted, “ No Common
5. When no module is inserted, “ No Common
Interface module detected ” message appears
on the screen.
You can refer to the module instruction manual for details
You can refer to the module instruction manual for details
of the settings.
CAM
m
odule
Standby Notif cations
If the TV does not receive any input signal (e.g. From
an aerial or HDMI source) for 5 minutes, the TV will
go into standby. When you next switch-on the TV, the
following message will be displayed:
When the Auto Tv Off timeout is reached, the following
message will be displayed on the screen. Select YES
to shut down the TV. Select NO to cancel. The TV
will switch off as well, if you do not make a selection
on this screen.
If the TV has been left on and not been operated for
4 hours, the TV will go into standby. When you next
switch-on, the following message will be displayed:
A01_[GB]_mb95_4847uk_DVBT_C_S2_DLNA_HBBTV_MMH_32205LED_39205LED_GOLD19_10081423-10081425-10082975-10083449_50231035_basic IB.indd 11
29.01.2013 18:37:50
English - 12 -
Installing the Batteries to the Remote
1. Lift the cover on the back of the remote upward
gently.
2. Install two AAA batteries. Make sure to match the +
2. Install two AAA batteries. Make sure to match the +
and - ends of the batteries in the battery compartment
(observe the correct polarity.
3. Replace the cover.
3. Replace the cover.
Connect Power & Antenna/Cable/Satellite
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket. After unpacking, allow
the TV set to reach the ambient room temperature
before you connect the set to the mains. Plug the
power cable to the mains socket outlet.
Aerial or Cable
Satellite
DiSEqC
Switch
SPDIF
VGA
300mAMax.
HDMI2
HDMI3
13V dc/18V dc
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC 50 Hz.
Switch the “
” button on the bottom right hand side
under the screen to position “|” so the TV will switch
to standby mode. Then the standby LED lights up.
To switch on the TV from standby mode either:
• Press the “ ” button,
To switch on the TV from standby mode either:
• Press the “ ” button,
P+ / P- or a numeric button
on the remote control.
• Press the “ ” or
P/CH+/- button on the TV.
The TV will then switch on.
Note: If you switch on your TV via P+ / P-
buttons on the
remote control or P/CH+/- on the TV set, the programme that
you were watching last will be reselected.
you were watching last will be reselected.
To Switch the TV to Standby
To switch the TV to low power stand by press the
“ ” button on the remote control or on the TV.
“ ” button on the remote control or on the TV.
Note: When the TV is switched to standby mode, standby LED
can blink to indicate that features such as Standby Search,
Over Air Download or Timer is active.
can blink to indicate that features such as Standby Search,
Over Air Download or Timer is active.
To Switch the TV Off
Switch the “
” button on the bottom right hand side
under the screen to position 2 as illustrated,
, to
isolate the TV from the mains, the LED will go
out.
First Time Installation
When turned on for the f rst time, the “language
selection” menu appears. The message “
Welcome
please select your language! ” is displayed in all
language options listed alphabetically.
Press the “
” or “
” button to highlight the required
language, press
OK button to select. “First Time
Installation” appears. Use “ ” or “ ” button to set the
required country, and press “
” button to select Search
Type. Use “ ” or “ ” to set the desired search type.
Available search types are Digital and analog, digital
only and analog only. When set, press “
” to select
Teletext Language. Use “ ” or “ ” button to set the
“Teletext Language” and select “Scan Encrypted” using
“
” or “
” button. You can set
Scan Encrypted as
Yes if you want to scan coded stations.
A01_[GB]_mb95_4847uk_DVBT_C_S2_DLNA_HBBTV_MMH_32205LED_39205LED_GOLD19_10081423-10081425-10082975-10083449_50231035_basic IB.indd 12
29.01.2013 18:37:51
Click on the first or last page to see other LC-32LE351K (serv.man2) service manuals if exist.