Read Sharp LC-32LE210E (serv.man7) Service Manual online
16
LC-32LE210
LC-32LE220
LC-32LE220
SERVICE ADJUSTMENTS
1. Adjustment method after PWB and/or IC replacement due to repair
The unit is set to the optimum performance at the time of shipment from the factory.
If any value should become improper or any adjustment is necessary due to the part replacement, make an adjust-
ment
according
to
the
following
procedure.
1.1. Procure the following units in order to replace the main unit:
MAIN
UNIT
DUNTKF639FMxx
NOTE: [Caution when replacing ICs in the main unit (IC1901, IC1902, IC1902, IC1501, IC1006 and IC1007)]
Before replacing the relevant part, procure the following parts in which the data have been rewritten.
Ref.
Description
Parts code IC + data
Description new IC code for service
IC1901
HDMI EDID 1
RH-IXD236WJZZY
RH-IXD080WJZZY AND DATA LC32LE2x0E_HDMI_1_EDID
IC1902
HDMI EDID 2
RH-IXD237WJZZY
RH-IXD080WJZZY AND DATA LC32LE2x0E_HDMI_2_EDID
IC1903
HDMI EDID 3
RH-IXD238WJZZY
RH-IXD080WJZZY AND DATA LC32LE2x0E_HDMI_3_EDID
IC1501
PC EDID
RH-IXD239WJZZY
RH-IXD080WJZZY AND DATA LC32LE2x0E_PC_EDID
IC1006
HDCP USER SETTINGS
RH-IXD261WJZZY
RH-IXC986WJZZY AND DATA LC32LE2x0E_HDCP_KEY
IC1007
*
FLASH
MEMORY
MEMORY
RH-IXD262WJZZY
RH-IXD012WJZZY and LE210_v1.25_PANEL_AUO_BOARD_N1
RH-IXD263WJZZY
RH-IXD012WJZZY and LE210B_v1.25_PANEL_CMI_BOARD_N1
2. Entering and exiting the adjustment process mode. Standard method.
1. By key-unit.
1. Unplug the AC power cord.
2. Press and hold “V-” and “
b” keys, simultaneously, and then plug the AC power cord.
3. “K” appears on the screen.
4. Press and hold “V-” and “P-” keys, simultaneously.
5. “SHARP FACTORY MENU” appears (see Figure 1).
6. Unplug the AC power cord to exit of adjustments process.
2. By own R/C
1. Turn on the TV set.
2. Press “
b”,”2”,”5”, “8”, “0” (the time is limited to 5 sec. approx., for enter this code).
3. “SHARP FACTORY MENU” appears (see Figure 1).
4. Press “OK” on lines 5 ~ 12 to go to submenu.
5. Press “MENU” to return to main menu.
6. Press “END” to exit of adjustments mode.
* For Lx220 models it is not possible replace IC1007. Replace the full Main Unit.
17
LC-32LE210
LC-32LE220
LC-32LE220
3. Remote control key operation and description of display in adjustment process mode.
1. key operation
Remote control key
Keyboard unit
Function
Cursor (
ź/Ÿ )
P (
s
/
r
)
Moving an item (line) by one (up/down) on “Sharp Factory Menu”
or submenus.
or submenus.
OK
b
Selecting a submenu on lines 5 to 12 of “Sharp Factory Menu” or
executing a function.
executing a function.
Cursor (
Ż/Ź)
V (+/-)
Changing a selected item setting value.
MENU
MENU
Return to “Sharp Factory Menu” from a submenu.
The required input mode should be switched previously to enter the Service Mode.
CAUTION: Use due care in handling the information described here lest the users should know how to enter the
adjustment process mode. If the settings are tampered with in this mode, unrecoverable system
damage may result.
4. Description of display
Figure 1: Main Service Adjustment Menu
ĸ Informative (Main microprocessor version).
ĸ Informative.
ĸ Informative (Remote Control/Keyboard…).
ĸ Informative (None/Lamp Error).
ĸ Press “OK” to go to INIT submenu.
ĸ Press “OK” to go to ADJUST submenu.
ĸ Press “OK” to go to ETC submenu.
ĸ Press “OK” to go to PUBLIC MODE submenu.
ĸ Press “OK” to go to SMARTLOADER submenu.
ĸ Press “OK” to go to ADC ADJUST submenu.
ĸ Press “OK” to go to GAMMA submenu.
ĸ Press “OK” to go to SYSTEM INFORMATION submenu.
ĸ Informative.
ĸ Informative (Remote Control/Keyboard…).
ĸ Informative (None/Lamp Error).
ĸ Press “OK” to go to INIT submenu.
ĸ Press “OK” to go to ADJUST submenu.
ĸ Press “OK” to go to ETC submenu.
ĸ Press “OK” to go to PUBLIC MODE submenu.
ĸ Press “OK” to go to SMARTLOADER submenu.
ĸ Press “OK” to go to ADC ADJUST submenu.
ĸ Press “OK” to go to GAMMA submenu.
ĸ Press “OK” to go to SYSTEM INFORMATION submenu.
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
ĸ
SHARP FACTORY MENU
Main version
32LE210E SHARP v1.25 SEES v89 MSTAR CL308413
Bootloader version
BD_MST064E_C01A 2
Normal standby cause
Remote control
Error standby cause
None
INIT
ADJUST
ETC
PUBLIC MODE
SMARTLOADER
ADC ADJUST
GAMMA
SYSTEM INFORMATION
No.
Description
Display speci cation
(1)
Service Information
Current Software version and others.
(2)
Item name
Submenus to be checked or adjusted (by pressing “OK” button)
(3)
Factory init and Inch setting
Are shown on INIT submenu
(2)
(3)
33
1
8
08
30
3
C
C
S
9
89
8
S
S
S
2
1
S
S
0
1
22
2
32
3
1
(1)
18
LC-32LE210
LC-32LE220
LC-32LE220
Page
Line
Sub
Page
Item
Description
Remarks (adjustment details, etc.)
01/17
[SHARP FACTORY MENU
1
Main Version
32LE210E SHARP v1.25 SEES
v89 MSTAR CL308413
v89 MSTAR CL308413
Informative only (Main microprocessor version)
2
Bootloader Version
BD_MST064E_C01A 2
Informative only
3
Normal Standby Cause
Remote Control / Keyboard...
Informative only
4
Error Standby Cause
None / Lamp Error
Informative only
5
INIT
Factory Init Submenu
Press “OK” to enter to Factory Init Submenu
02/17 Factory
Init
EURO
Informative (EURO/RUSSIA/SWEDEN/UK/EAST EUROPE)
Inch Setting
AV32_T315HW05V3
Panel type
Center Acutime
0 H 0 M
Backlight ON accumulated Time
RESET
“OK” Will be displayed
Press “
Ż “ or “ Ź” to reset Center Acutime
6
ADJUST
QMAP ADJUST Submenu
Press “OK” to enter to QMAP ADJUST Submenu
03/17
INPUT SOURCE (1/6)
RF_PAL_BGHI
AFEC
Only for Engineering purpose (Please don’t use)
Comb
Only for Engineering purpose (Please don’t use)
SECAM
Only for Engineering purpose (Please don’t use)
SCinit
Only for Engineering purpose (Please don’t use)
CSC
OFF
Only for Engineering purpose (Please don’t use)
CSC_Dither
OFF
Only for Engineering purpose (Please don’t use)
YCdelay
OFF
Only for Engineering purpose (Please don’t use)
PreFilter
OFF
Only for Engineering purpose (Please don’t use)
HSD_Y
ALL PASS1X
Only for Engineering purpose (Please don’t use)
HSD_C
ALL PASS1X
Only for Engineering purpose (Please don’t use)
VSD
OFF
Only for Engineering purpose (Please don’t use)
CTI
CTI_1
Only for Engineering purpose (Please don’t use)
04/17
INPUT SOURCE (2/6)
DTV/ RF/Multimedia ...
MemFormat
422MF
Only for Engineering purpose (Please don’t use)
444To422
ON
Only for Engineering purpose (Please don’t use)
PreSNR
OFF
Only for Engineering purpose (Please don’t use)
DNR
NR_OFF
Only for Engineering purpose (Please don’t use)
DNR_Motion
MR_NR
Only for Engineering purpose (Please don’t use)
DNR_Y
OFF
Only for Engineering purpose (Please don’t use)
DNR_MED
OFF
Only for Engineering purpose (Please don’t use)
DNR_C
OFF
Only for Engineering purpose (Please don’t use)
PNR
OFF
Only for Engineering purpose (Please don’t use)
PNR_Y
OFF
Only for Engineering purpose (Please don’t use)
PNR_C
OFF
Only for Engineering purpose (Please don’t use)
PostCCS
OFF
Only for Engineering purpose (Please don’t use)
05/17
INPUT SOURCE (3/6)
DTV/ RF/Multimedia ...
PostCCS_Smooth
PCS_6
Only for Engineering purpose (Please don’t use)
420CUP
OFF
Only for Engineering purpose (Please don’t use)
MADi
25_4R
Only for Engineering purpose (Please don’t use)
MADi_Motion
MOT_PMODE
Only for Engineering purpose (Please don’t use)
MADi_ADP3x3
OFF
Only for Engineering purpose (Please don’t use)
MADi_MORPHO
OFF
Only for Engineering purpose (Please don’t use)
MADi_DFK
OFF
Only for Engineering purpose (Please don’t use)
5. Adjustment process mode menu
19
LC-32LE210
LC-32LE220
LC-32LE220
Page
Line
Sub
Page
Item
Description
Remarks (adjustment details, etc.)
1/17
[SHARP FACTORY MENU
6
ADJUST (continued)
QMAP ADJUST Submenu
Press “OK” to enter to QMAP ADJUST Submenu
05/17
INPUT SOURCE (3/6)
DTV/ RF/Multimedia ...
MADi_SST
OFF
Only for Engineering purpose (Please don’t use)
MADi_Force
OFF
Only for Engineering purpose (Please don’t use)
EODi
OFF
Only for Engineering purpose (Please don’t use)
Film
SD_2
Only for Engineering purpose (Please don’t use)
Film32
OFF
Only for Engineering purpose (Please don’t use)
06/17
INPUT SOURCE (4/6)
DTV/ RF/Multimedia ...
Film22
OFF
Only for Engineering purpose (Please don’t use)
DIPF
OFF
Only for Engineering purpose (Please don’t use)
VCLPF
ON
Only for Engineering purpose (Please don’t use)
Spike_NR
S2
Only for Engineering purpose (Please don’t use)
SPF
ON
Only for Engineering purpose (Please don’t use)
SPF_DBK
OFF
Only for Engineering purpose (Please don’t use)
SPF_SNR
E2S1
Only for Engineering purpose (Please don’t use)
SPF_DBK_SNR_MR
ON
Only for Engineering purpose (Please don’t use)
SPF_MR_LPF
LPF3x3
Only for Engineering purpose (Please don’t use)
SPF_SMR
S2
Only for Engineering purpose (Please don’t use)
SPF_NMR_MR
ON
Only for Engineering purpose (Please don’t use)
DMS
S2
Only for Engineering purpose (Please don’t use)
07/17
INPUT SOURCE (5/6)
DTV/ RF/Multimedia ...
VSP_Y
SRAM_1_4Tap
Only for Engineering purpose (Please don’t use)
VSP_C
ROM_2121
Only for Engineering purpose (Please don’t use)
VSP_CoRing
OFF
Only for Engineering purpose (Please don’t use)
VSP_DeRing
OFF
Only for Engineering purpose (Please don’t use)
VSP_Dither
OFF
Only for Engineering purpose (Please don’t use)
VSP_PreVBound
OFF
Only for Engineering purpose (Please don’t use)
HSP_Y
SRAM_2_6Tap
Only for Engineering purpose (Please don’t use)
HSP_C
ROM_121
Only for Engineering purpose (Please don’t use)
HSP_CoRing
Y_Coring_1
Only for Engineering purpose (Please don’t use)
HSP_DeRing
OFF
Only for Engineering purpose (Please don’t use)
HSP_Dither
OFF
Only for Engineering purpose (Please don’t use)
HnonLinear
H_1920_0
Only for Engineering purpose (Please don’t use)
08/17
INPUT SOURCE (6/6)
DTV/ RF/Multimedia ...
SRAM1
lnvSinc4Tc4p4Fc85
Fstop134Apass01Astop50
Only for Engineering purpose (Please don’t use)
SRAM2
lnvSinc6Tc4p4Fc94
Fstop134Apass01Astop60
Only for Engineering purpose (Please don’t use)
422To444
ON
Only for Engineering purpose (Please don’t use)
Peaking
1080p
Only for Engineering purpose (Please don’t use)
SwDriver
ALL
Only for Engineering purpose (Please don’t use)
VIP_CSC
OFF
Only for Engineering purpose (Please don’t use)
VIP_CSC_Dither
OFF
Only for Engineering purpose (Please don’t use)
Color
Multimedia_photo_HD
Only for Engineering purpose (Please don’t use)
3x3
OFF
Only for Engineering purpose (Please don’t use)
Display
ALL
Only for Engineering purpose (Please don’t use)
Post_CON_BRI
OFF
Only for Engineering purpose (Please don’t use)
