Read Sharp LC-22LE240K Service Manual online
14
LC-22LE240
Operation Manual (Continued)
English
- 13 -
Connecting the LCD TV to a PC
For displaying your computer’s screen image on your
LCD TV, you can connect your computer to the TV set.
Power off both computer and display before making
any connections. Use 15-pin D-sub display cable to
connect a PC to the LCD TV. When the connection
is made, switch to PC source. See “Input selection”
section. Set the resolution that suits your viewing
requirements. Resolution information can be found
in the appendix parts
.
PC Input
(back)
Side AV Input
PC VGA Cable
(not supplied)
PC Audio Cable
(not supplied)
Side Audio/Video
Connection Cable
(supplied)
or
SIDE
AV
Using Side AV Connectors
You can connect a range of optional equipment to your
LCD TV using side connectors of the TV.
For connecting a camcorder or camera , you should
•
use AV socket (side). To do this, you must use the
supplied video/audio connection cable. First, plug
single jack of the cable to the TV’s AV IN socket
(side). Afterwards, insert your camera cable’ s (not
supplied) connectors into the
socket
part of the
video/audio connection cable
. Colours of the
connected jacks should match. See illustration
below.
Afterwards, you should switch to
Afterwards, you should switch to
•
Side AV
source. See
the section Input selection in the following sections
for more information.
Camera
AV Connection
Cable (supplied)
AV Cable
(not supplied)
Headphone
SIDE
AV
To listen the TV sound from headphones, you
•
should connect headphones to your TV by using the
HEADPHONE
HEADPHONE
jack as illustrated above..
Remote Control Handset
Inserting Batteries
Remove the battery cover located on the back of
•
the handset by gently pulling backwards from the
indicated part.
Insert two
Insert two
•
AAA/R3
or equivalent type batteries
inside. Observe the correct polarity (+/-) when
inserting batteries and replace the battery cover.
Note
: Remove the battery from remote control
handset when it is not to be used for a long period.
Otherwise it can be damaged due to any leakage of
batteries. Remote range is approximately 7m/23ft.
Switching On/Off
To Switch the TV On
Connect the power cord to the 220-240V AC 50 Hz.
Switch the “
•
” button on the bottom right hand
side under the screen to
position “|” so the TV will
switch to standby mode. Then the standby LED
lights up.
To switch on the TV from standby mode either:
To switch on the TV from standby mode either:
•
Press the “
•
” button,
CH / CH
or a numeric
button on the remote control.
Press the “
Press the “
•
” or +/- button on the TV.
The TV will then switch on.
•
Note : If you switch on your TV via
Note : If you switch on your TV via
CH / CH
buttons
on the remote control or on the TV set, the programme
that you were watching last will be reselected.
By either method the TV will switch on.
By either method the TV will switch on.
To Switch the TV to Standby
To switch the TV to low power stand by press the
“ ” button on the remote control or right hand side
“ ” button on the remote control or right hand side
of the TV.
Note
Note
: When the TV is switched to standby mode,
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or T imer is
active.
To Switch the TV Off
•
Switch the “
” button on the bottom right hand
side under the screen to position 2 as illustrated,
to isolate the TV from the mains, the LED will
go out.
00_MB62_[GB]_1910UK_UK IDTV_PVR_BRONZE19_22942LED_ROCKER_10076196_5020xxxx.indd 13
05.03.2012 12:54:46
Click on the first or last page to see other LC-22LE240K service manuals if exist.