66GF-64 (serv.man15). Split - Part 5 - Features setting mode - page 22-25 - Sharp TV User Guide / Operation Manual

66gf-64 (serv.man15) user guide / operation manual
Model
66GF-64 (serv.man15)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
458.44 KB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
TV / CTR / Split - Part 5 - Features setting mode - page 22-25
File
66gf-64-sm15.pdf
Date

Read Sharp 66GF-64 (serv.man15) User Guide / Operation Manual online

22
Web-site: www.sharp.co.uk/support
Help Line (office hours only): 0990-274277
Features setting mode
In this mode you can set the ON-TIMER and OFF-TIMER, set the CHILD LOCK, activate or deactivate the interactive
HELP, view the all functions implemented in your TV set demonstration and set the Post code.
1.
Press the MENU button 
to see the MAIN Menu.
2.
Press the YELLOW button 
to see the Timer Menu.
ON-TIMER
The On-Timer is used to programme switching ON the TV set during
the 24 hours of the day.
In order to be able to run this function, it is essential to adjust the
current time
3.
Press the Cursor UP/DOWN buttons 
E
/
F
to select
“Current time”. The red point mark indicates the selected item.
Automatic  TIME adjustment: If a programme with teletext is being
received, the “Current time” can be adjusted automatically with that
signal's clock.
To synchronize “Current time”, press Text/Mix/Picture button 
a
/
b
/Q
.
*
Important: If a signal via satellite is being received, or if correct time
cannot be obtained, the time will have to be adjusted manually.
Manual time adjustment: Press the Cursor LEFT/RIGHT buttons  
/
I
to adjust the “Current time” manually.
4.
Press the Cursor UP/DOWN buttons  
E
/
F
to select “Programmed switch on at”. The red point mark
indicates the selected item.
5.
Press the Cursor LEFT/RIGHT buttons 
/
I
to adjust the switch on.
To cancel the switch on, select 
in on timer status.
6.
Press the MENU button 
to close the ON TIMER Menu.
7.
Press the Stand-by button ( 
¾ 
TV) on the remote control to put the TV set into Stand-by Mode.
Will inform a notice informing the hour TV will swich on.
When the preset time is reached, the TV set turns ON and a picture appears on the screen.
* As a safety precaution, in the case of nobody being home when the television switches on automatically, the television
will disconnect itself after 120 minutes; if it is to continue to run any of the remote control function buttons should be
pressed.
Note: In the event of a power cut, disconnection from the plug or television switch, all the data on the ON TIMER will be
cancelled.
OFF -TIMER
The OFF-Timer is used to programme switching the TV set to Stand-by
mode, after the set length of time has passed.
If necessary, repeat steps (1. ~ 2.) to see the Timer Menu.
3.
Press the Cursor UP/DOWN buttons  
E
/
F
to select   “Off
timer status”. The red point mark indicates the selected item.
4.
Press the Cursor LEFT/RIGHT buttons  
/
I
to select the desired
period (maximum 180 minutes in periods of five minutes).
To cancel the OFF-Timer, select 
.
5.
Press the MENU button 
to close the OFF -TIMER Menu.
Note: The off timer data will be cancelled if you turn off the TV by the
Stand-by button ( 
¾ 
TV) on the remote control or with the Main power
button (
¨
) on the TV set.
MAIN Menu
TIMER Menu
TIMER Menu
23
Web-site: www.sharp.co.uk/support
Help Line (office hours only): 0990-274277
Help
Your TV  is provided with Interactive Help, indicated on screen with the 
symbol, which contain guidance for TV
operation. With the option Help On/Off, you can display or hide the Help boxes.
1.
Press the MENU button  
to see the MAIN Menu.
2.
Press the YELLOW button 
to see the Timer Menu.
3.
Press the Cursor UP/DOWN buttons 
E
/
F
to select
“Help”. The red point mark indicates the selected item.
4.
Press the Cursor LEFT/RIGHT buttons   
/
I
to activate (On)
or deactivate (Off) the Interactive Help.
5.
Press the MENU button  
to close the Menu.
The demonstration function allows you to see all the menus implemented in this TV set.
1.
Press the MENU button 
to see the MAIN Menu.
2.
Press the YELLOW button 
to see the Timer Menu.
3.
Press the GREEN button 
to see the DEMO Menu.
4.
Press the Cursor LEFT/RIGHT buttons  
/
I
to select: full or
autoinstallation
5.
Press the BLUE button 
to begin the demonstration.
6.
Press any button on the remote control to exit this function when you wish.
This option allows you to set a code which will be displayed at TV switch on time. There is a password to change thecode.
1.
Press the MENU button 
to see the MAIN Menu.
2.
Press the YELLOW button 
to see the Timer Menu.
3.
Press the BLUE button 
to see the POST CODE Menu.
4.
Password: enter the 4-digit using the number buttons.
It is indispensable to enter the «Password» in order to continue
configuring the «Post Code».
5.
Press the BLUE button 
to memorize the «Password» or to
have access to the next item.
6.
Press the Cursor DOWN button 
F
to select «Post code».
7.
Press the Cursor RIGHT button  
I
to select the first position.
8.
Press the Cursor UP/DOWN buttons  
E
/
F
to set or
change the first letter/number. Letters A to Z of the alphabet, a
blank space and the numbers 0 to 9 will appear sequentially.
9.
Press the 
I
button for changing the position of the cursor and
the    
E
/
buttons for changing the letters (repeat this
action for other letters/numbers).
10. When you have finished the eighth letter, press the 
I
button to quit the «Post code» box.
11. Press the BLUE button 
to memorize the «Post Code».
If you wish to cancel all the data, select «Eliminate post code and password» and press the BLUE button 
.
12. Press the MENU button 
to close the Menu.
About Post code: If you memorize a «Post Code», in the event of lose or robbery of TV set and later recovery,
you can identify your TV set by «Post Code».
Notes: As a precautionary measure, make a note of your «Password» and the «Post Code», and keep it in a
familiar place.
IF YOU LOSE OR FORGET YOUR «PASSWORD», CONTACT YOUR TECHNICAL SERVICE OR DEALER.
Demo
Post code
TIMER Menu
DEMO Menu
POST CODE Menu
FULL
24
Web-site: www.sharp.co.uk/support
Help Line (office hours only): 0990-274277
Child lock (Protection)
You can lock a TV channel to prevent unsupervised TV viewing by following these procedure.
The protection can apply to the television itself «LOCK ALL» or to specific programmes «LOCK PROGRAMME». With the
CHILD LOCK function, you can also programme a time period during which the TV or the programmes will be protected.
(Your children can not select the channel which you locked).
Because the remote control is the “KEY” to unlock the TV, you must
remember not to let the remote control out of your supervision.
1.
Press the MENU button  
to see the MAIN Menu.
2.
Press the YELLOW button 
to see the Timer Menu.
Timer Menu
3.
Press the RED button 
to see the LOCK ALL Menu.
LOCK ALL Menu
Use this option for protecting the access to the whole TV.
If you wish to block some specific programme, press the
YELLOW button 
and proceed to stage 5. - LOCK
PROGRAMME - on the next page.
4.
Press the Cursor LEFT/RIGHT buttons 
/
I
to select an option:
NONE: To cancel the protection.
ALWAYS: The access to the TV will be protected throughout the day.
TIMER: The access to the TV will be protected during the programmed
period.
5.
If you have selected TIMER, press the Cursor UP/DOWN buttons
E
/
to select:
Start : To enter the hour and minutes, from the beginning of protection, with the Cursor LEFT/RIGHT buttons 
/
I
.
End: To enter the hour and minutes, to the end of protection, with the Cursor LEFT/RIGHT buttons  
/
I
.
6.
Press the MENU button 
● 
to close the LOCK ALL Menu.
MAIN Menu
Timer Menu
LOCK ALL Menu
25
Web-site: www.sharp.co.uk/support
Help Line (office hours only): 0990-274277
LOCK PROGRAMME Menu
Use this option to protect the access to separate programmes.
If necessary, repeat steps (1. ~ 3.) .
4.
Press the YELLOW button 
to see the LOCK
PROGRAMME Menu.
5.
Select the programme channel number you want to set with the
Cursor LEFT/RIGHT buttons 
/
I
.
6.
Press the Cursor UP/DOWN buttons  
E
/
F
to select
“Type of protection”. The red point mark indicates the selected
item.
7.
Press the Cursor LEFT/RIGHT buttons  
/
I
to select an
option:
NONE: To cancel the protection from the selected programme.
ALWAYS: To protect the access from the selected programme
throughout the day
AUTO (VPS CODE): To activate the AUTOMATIC PROTECTION and the selected programme will only be blocked
when it receives the VPS signal. This VPS signal is sent by some broadcasting stations, when the programme that
is being shown is not suitable for children.
TIMER: The access to the selected programme will be protected during the programmed period.
8.
If you have selected TIMER, press the Cursor UP/DOWN buttons  
E
/
F
to select:
Start : To enter the hour and minutes, from the beginning of protection, with the Cursor LEFT/RIGHT buttons 
/
I
.
End: To enter the hour and minutes, to the end of protection, with the Cursor LEFT/RIGHT buttons 
/
I
.
9.
Press the MENU button 
● 
to close the LOCK PROGRAMME Menu.
CLEAR LOCK Menu
This option enables you to erase all the adjustments made to the
CHILD-LOCK function.
If necessary, repeat steps (1. ~ 3.).
4.
Press the BLUE button 
to see the CLEAR LOCK Menu
5.
Press the BLUE button 
to confirm you want to clear the
Notes:In order for the timed protection to function correctly, the internal TV clock must be set at the right time. To
check the time setting see section - Automatic or Manual time adjustment - (page 22).
When you protect one programme, all the external entries (Euro-SCART, AV-1, AV-2, Front A/V or S-Video
terminals) are protected automatically.
Access to protected modes
LOCK ALL:
When the TV is protected in this way, it will be blocked when switched on and a red box will appear on the screen
(against a blue background), along with the instruction « LOCKED MODE ».
In order to view your TV you must press any digit button  0 ~ 9  of the remote control.
If the protection is timed, the blocking of the TV will only occur during the time period programmed.
LOCK PROGRAMME:
When one or several programmes are protected, the TV will block any attempt to gain access to them and the
instruction « LOCKED MODE » will appear on the screen.
In order to view these programmes you must press any digit button  0 ~ 9  of the remote control.
If the protection of the programme you want to gain access to is timed or automatic, the blocking of the
programme will only take place during the time period programmed or on receiving the special VPS signal for
automatic blocking.
LOCK PROGRAMME Menu
CLEAR LOCK Menu
Page of 4
Display

Download Sharp 66GF-64 (serv.man15) User Guide / Operation Manual

Here you can read online and download Sharp 66GF-64 (serv.man15) User Guide / Operation Manual in PDF. 66GF-64 (serv.man15) user guide / operation manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp 66GF-64 (serv.man15) CTR. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.