37GT-27H (serv.man6). Hotel mode - Sharp TV Service Manual (repair manual)

Below listed can be found the procedure to carry out in the above TV Sets functions called HOTEL MODE as follows:
Consider that  HOTEL MODE is implemented by means of HOTEL MODE 1. The HOTEL MODE 2 or HOTEL MODE 3
can be used at the same time than HOTEL MODE 1.

Hotel 1 Mode: blockade of the TUNING function by modifying the value in 0A address of the NVM.
-This change besides blocking the tuning function, makes the TV always starts to operate in program 1.

Procedure:

A) Press the volume up or volume down buttons (RC) as far as the NVM address  (green colour) displays “0A” location.
Check the NVM value (red colour) displays the NORMAL VALUE .

B) Pay Attention: Press  the button 2 (RC) only once. The NORMAL VALUE has been changed to the HOTEL 1 MODE
VALUE now. If the button 2 (RC) is pressed again the NORMAL VALUE is recovered. For the same reason, if  a wrong
button has been pressed, NORMAL VALUE can be recovered by pressing the same button again. See NVM table on
page 6.

Restriction of Sound Volume: by modifying the value in 0E address of the NVM.
Notes:
a) Before blocking the tuning function is necessary to memorise the programs according to the necessities of the destina-
tion  hotel.
b) Since the Hotel Mode functions have been programmed the end users of the television won’t be able to tune different
channels neither to erase the existent ones.

1.8.  Exit Service Mode and check colour coordinates «X» and «Y» at 20 and 120 nits. It may be necessary to repeat the
    same procedure or readjust the cuts as show the be below one.

2. «CUT R», «CUT G»
2.1.  Adjust G2, in the case that it has not been made previously.
2.2. Tune a grey scale pattern.
2.3.  Adjust colour to minimum.
2.4.  Position colorimeter in the right point of Fig.4.
2.5.  Using brightness and contrast buttons, select a luminance of »20 nits.
2.6.  Operate again in Service Mode and select location CUT-G and CUT-R to obtain colour coordinates:

X = 0.290 ± 0.015
Y = 0.284 ± 0.015

2.7.  Exit Service Mode and check colour coordinates «X» and «Y» at 20 and 120 nits. It may be necessary to repeat
        the same procedure or the previous one.

The following process describes how to cancel actual password (PIN) when the customer forgets the code.

1.  Press channel up or down to select the channel, wich you locked with input PIN number.
2.  The TV picture will be blue and the key appear on screen.
3.  Press and hold volume down on the TV and simultaneously press CHILD LOCK button (see Page.43) on the remote
     control several times until the key disappears.

c) Neither one will be able to get the sound volume in a superior level to the maximum limited in each case.

Procedure:

A)  Press  the volume up or volume down buttons as far as the NVM address displays 0E location.

Hotel 2 Mode: by modifying  the value in 57 address of the NVM .
-When the TV set is switched on by main it starts working in SCART mode.
-When the TV is in STAND-BY mode  and it is connected to a VCR through a 21 pins wire, it may be switched on simply
by SLOW SWITCH (VCR in PLAY mode).
-In these circumstances the Front Panel Control Keys does not work.

Procedure:

A) Press the volume up or volume down buttons (RC) as far as the NVM address  (green Colour) displays “57” location.
Check the NVM value (red colour) displays the NORMAL VALUE . See NVM Table on page 8.

B) Pay Attention: Press  the button 0 (RC) only once. The NORMAL VALUE has been changed to the HOTEL 2 MODE
VALUE now. If the button 0 (RC) is pressed again the NORMAL VALUE is recovered.  For the same reason, if  a wrong
button has been pressed, NORMAL VALUE can be recovered by pressing the same button again.

Hotel 3 Mode: by modifying the value 57 address of the NVM.
-When this it is activated VCR mode is set in all programs.

Procedure:

A) Press the volume up or volume down buttons (RC) as far as the NVM address  (green colour) displays “57” location.
Check the NVM value (red colour) displays the NORMAL VALUE.

B) Pay Attention: Press  the button 1 (RC) only once. The NORMAL VALUE has been changed to the HOTEL 3 MODE
VALUE now. If the button 1 (RC) is pressed again the NORMAL VALUE is recovered. For the same reason, if  a wrong
button has been pressed, NORMAL VALUE can be recovered by pressing the same button again. See NVM Table on
page 8.

Check the Hotel Functions work OK.

                    BUTTON   (RC)         VALUE               SOUND VOL.
                 TO BE PRESSED       STORED               LIMITED TO
                              (4)(3)               (EF)(E7)                       90%
                              (5)(4)               (DF)(CF)                       80%
                                (6)                     (BF)                          73%
                              (6)(5)               (BF)(9F)                       62%