Read Sharp 21LF-90H Handy Guide online
1
2
4
SUPPLIED ACCESORIES
Remote Control
- Fitting the batteries
-
2
3
TYPICAL CONNECTIONS
TYPICAL CONNECTIONS (Continued)
Mains Socket Outlet
AC 220~240 V, 50 Hz
Mains Socket Outlet
AC 220~240 V, 50 Hz
AV/TERMINAL
BACK OF TV
ANT.
EXT.1
DVD PLAYER
DECODER
Scart Lead
(Not supplied)
Scart Lead
(Not supplied)
Aerial IN
Scart Lead
(Not supplied)
Aerial Lead
(Not supplied)
Aerial
(Not supplied)
Aerial IN
Audio/Video
BACK OF VCR
RF OUT
Operation Manual
+
-
+
-
R03 ("AAA" size) Dry Batteries
1. With your thumb
nail, pull up the
slit as shown.
2. Insert the two
batteries as shown.
3. Replace the battery cover.
A SCART lead (not supplied) is recommended for use with this TV, to
obtain the best communication between your TV and VCR, refer
to
peration manual.
page 25 of the o
Check List:
• Is the TV connected to the mains?
• Is the aerial connected to the TV?
TURN ON TV FOR THE FIRST TIME
TV set
Main power button
1
2
3
Aerial IN
Back of TV
Aerial
(Not supplied)
Aerial Lead
(Not supplied)
ANT.
SCART
Mains Socket Outlet
AC 220~240 V, 50 Hz
Initial Settings
The message “
” will be displayed when you turn on your
TV for the first time.
PLEASE CHECK ANTENNA CABLE AUTO.
PROGRAMMING SYSTEM
1-
LANGUAGE
2-
COUNTRY
STANDARD
4-
START
A.P.S.
A.P.S.
A.P.S. A.P.S. IS RUNNING
A.P.S.
PROGRAM.
Select
with “ ” or “
” button, then press the
“ ” or “ ” button to select a menu language.
Select
with “ ” or “
” button, then press the
“ ” or “ ” button to select the correct country.
Press the “ ” or “
” buttons to select “
”. This,will
effect the sort process in APS.
Select
with “ ” or “
” button, then press the “ ” button
to start
, (Automatic Programming System) automatically
programmes the received channels in your TV’s programme
numbers. During
, “
” will be displayed.
After
is finalized, the “
” menu appears.
To cancel APS during running press “ ” or “ ” button.
3-
I
f you do not accept the locations and / or the programme names of
programmes, you can change them in “
” on
PROGRAM. (Programming
menu
page 16.)
Your TV will switch on in two steps:
Press the Main power button ( ) located
on the front of the TV.
To switch on the TV from stand-by mode either:
Press a digit button on the remote control so
that a programme number is selected,
or,
1-
2-
This will switch the
TV into Stand-by mode. The LED at the
front of the TV will illuminate red.
Press Power button and “
” or “
” buttons on the TV or “
” or
“
” buttons on the remote control respectively, so the TV will switch
on and the
Led will turn
.
CH
CH
-P/CH
P/CH+
RED
GREEN
R
Please read this operation manual carefully
before using the colour television.
21LF-90H
COLOUR TELEVISION
OPERATION MANUAL
SCART
ANT.
SCART
ANT.
A.P.S.
PLEASE CHECK ANTENNA CABLE
AUTO. PROGRAMMING SYSTEM
LANGUAGE
START
COUNTRY
STANDARD
ENGLISH
UK
I
A.P.S. IS RUNNING
P 07 C12
CANCEL
CH
MENU
VIDEO
L- AUDIO -R
IN
R
21LF-90H
COLOUR TELEVISION
QUICK
START
GUIDE
For easy installation
Using this installation guide
should enable you to set up your
TV in less than 15 minutes - - -
- - - Refer to your operation
manual for more tips and advice
If problems persist, contact the SHARP Helpline (office hours only) on
tel : 08705 274277 (or(01) 676 0648 if telephoning from Ireland) and/or
WEB-SITE: www.sharp.co.uk/support
TV not plugged in Outlet power OFF
Main power button of TV not ON
Turn OFF using the Main Power button, then turn ON again
after a minute
Remote control
does not work
Check batteries in the Remote Control
Try a new channel to check for possible station trouble
If outside aerial is used, check for broken wires
Adjust COLOUR control
Try fine tuning to correct
Aerial not connected to terminal at the back of the TV set
No colour /
Picture weak
Try a new channel to check for possible station trouble
Aerial not connected to terminal at the back of the TV set
If outside aerial is used, check for broken wires
Check for local interference
Poor reception on
some channels
Try a new channel to check for possible station trouble
Aerial not connected to terminal at the back of the TV set
If outside aerial is used, check for broken wires
Check for local interference
Adjust COLOUR control
Try fine tuning to correct
Sound OK, poor picture
Check if the Brightness or Contrast setting in the picture
setting mode might be all the way to the minus side
Try a new channel to check for possible station trouble
Check for local interference
Increase the volume / Check Audio levels
Picture OK, poor sound
Try a new channel to check for possible station trouble
TV not plugged in Outlet power OFF
Main power button of TV not ON
Aerial not connected to terminal at the back of the TV set
If outside aerial is used, check for broken wires
Turn OFF using the Main Power button, then turn ON again
after a minute
Check if the Brightness or Contrast setting in the picture
setting mode might be all the way to the minus side
Increase the volume / Check Audio levels
No picture or sound
PROBLEMS
POSSIBLE CAUSES / REMEDIES
5
TROUBLESHOOTING
If the TV does not respond to the remote control or the buttons at the side
of the TV, please turn OFF the TV at the mains and retry.
SAFETY WARNINGS
1 - Select a well-ventilated location.
2 - Avoid exposing the TV set to direct sunlight,
dust, heat sources, or moisture.
3 - Do not place objects containing liquids or
candles on the top of the TV.
4 - Never open the back cover.
5 - Never insert objects into the TV.
6 - Take care not to damage the power cord.
7 - Keep the TV from strongly magnetic objects.
8 - To prevent fire, never place any type of candle
or naked flame on the top of or near the TV set.
R
SHARP ELECTRONICS
(U.K.) LTD.
Sharp House, Thorp Road, Newton Heath,
Manchester M40 5BE
SHARP CORPORATION
• Fitting the batteries into the remote control
• Connecting the aerial cable
• Tuning the TV channels
500*****
01/04
500*****
CH
MENU
CH
MENU
CH
MENU
Display
