Read Sharp 15JF-26H (serv.man7) Service Manual online
15JF-26H
12
•Hotel Mode Functions
The following procedure details how to set up the Hotel Mode Functions.
1. Short Description
1.1. Hotel Mode “HTL”: Main Hotel Mode. It deactivates “Channel Setting” functions. It reduces the Maximum Volume.
1.2. Hotel Mode “HTL-VOL”: Maximum Volume Level Regulation.
1.3 Hotel Mode “HTL-PRG”: Fixing start up program when the TV set is switched on.
2. Before start
2.1. It is necessary to program “Channel Setting” before setting up Hotel Mode “HTL” because after that Channel
Setting are deactivated.
2.2. Consider that regarding TXT Features, after activate any of the Hotel modes in the “List Mode” will not be stored
any page.
2.3. Consider that changed video control values are not stored.
3. Procedure
3.1. Hotel Mode “HTL” (Main Hotel Mode).
3.1.1. Previous Service Information: Initial Value: 0. Range: 0 to 1. Service Mode Indication: HTL.
3.1.2. Access the Service Mode (see this procedure on page 6).
3.1.3. Select “HTL” by using channel up/down buttons.
3.1.4. Change initial value from “0” (off ) to “1” (on).
3.1.5. Notes:
3.1.5.1. The maximum volume level has been reduced from 60 to 30. For other value go to 3.2. Hotel Mode
“HTL-VOL”
3.1.5.2. “Channel Setting” functions have been deactivated.
3.1.5.3. It is necessary to select Hotel Mode “HTL” to be able to set up Hotel Mode “HTL-VOL” or Hotel Mode
“HTL-PRG”.
3.1.5.4. If you do not need to set up Hotel Mode “HTL-VOL” or “HTL-PRG” get out from Service Mode (To
exit the Service Mode press the stand-by button on the remote control or turn the receiver off with
the mains switch).
the mains switch).
3.2. Hotel Mode “HTL-VOL” (Maximum Volume Level Regulation)
3.2.1. Previous Service Information: Initial value: 30. Range: 0 to 60. Service Mode indication: HTL-VOL.
3.2.2. To activate this Hotel Mode it is necessary activate previously Hotel Mode “HTL”. Then the maximum volume
level changed fro 60 to 30 as initial value.
level changed fro 60 to 30 as initial value.
13
15JF-26H
3.2.3. Select “HTL-VOL” by using channel up/down buttons.
3.2.4. Set the value according to your necessities by using volume up/down buttons.
3.2.5. Change initial value from “0” (off ) to “1” (on).
3.2.6. Note: If you do not need to set up Hotel Mode “HTL-PRG” get out from Service Mode (To exit the Service
Mode press the stand-by button on the remote control or turn the receiver off with the mains switch).
Mode press the stand-by button on the remote control or turn the receiver off with the mains switch).
3.3. Hotel Mode “HTL-PRG” (Fixing start up program when the TV Set is switched on)
3.3.1. Initial value: 255. Range: 0 to 255. Service Mode indication: HTL-PRG.
3.3.2. To activate this Hotel Mode it is necessary activate previously Hotel Mode “HTL”.
3.3.4. Select “HTL-PRG” by using channel up/down buttons.
3.3.3. The initial value to 255, ensures that the TV Set starts up in the same program number that it was been
displayed before turn it off.
displayed before turn it off.
3.3.4 If you want to fix other program number proceed as follows set the value according to your necessities by
using volume up / down buttons. Use values between 0 to 99. In this way, the new program number appear
fixed when you start up the TV set.
using volume up / down buttons. Use values between 0 to 99. In this way, the new program number appear
fixed when you start up the TV set.
Example: If you would like to set starting program number “2”, change from 255 to 2.
3.3.5. Get out from Service Mode (To exit the Service Mode press the stand-by button on the remote control or turn
the receiver off with the mains switch).
Display
