Read Sharp XV-Z200E (serv.man33) User Guide / Operation Manual online
Basic Operation
Basic Operation
XV_Z200E_E_p29_43.p65
03.10.30, 13:14PM
29
-30
Image Projection
-30
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
the projector before operating the following
procedures.
Info
• The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 31.
to another language, reset the language ac-
cording to the procedure on page 31.
1
Plug the power cord into the
wall outlet.
wall outlet.
• The POWER indicator illuminates red,
and the projector enters standby mode.
2
Press
on the remote control
or
on the projector.
• The blinking green LAMP indicator
shows that the lamp is warming up.
Wait until the indicator stops blinking
before operating the projector.
Wait until the indicator stops blinking
before operating the projector.
• If the power is turned off and then im-
mediately turned on again, it may take
a short while before the lamp turns on.
a short while before the lamp turns on.
Note
• After the projector is unpacked and
turned on for the first time, a slight
odour may be emitted from the ex-
haust ventilative holes. This odor will
soon disappear with use.
odour may be emitted from the ex-
haust ventilative holes. This odor will
soon disappear with use.
When the power is on, the LAMP in-
dicator illuminates, indicating the sta-
tus of the lamp.
Green: Lamp is ready.
Green blinking: Warming up. / Cooling
down.
Red: Change the lamp.
dicator illuminates, indicating the sta-
tus of the lamp.
Green: Lamp is ready.
Green blinking: Warming up. / Cooling
down.
Red: Change the lamp.
TEMP.
LAMP
POWER
LAMP indicator
POWER indicator
ON button
INPUT button
ON button
INPUT buttons
XV_Z200E_E_p29_43.p65
03.10.30, 13:14PM
30
Basic Operation
-31
3
Press
,
,
,
or
on the remote control or
on
the projector to select the IN-
PUT mode.
PUT mode.
• After pressing
once on the projector,
use
to select the desired input mode.
Note
• When no signal is received, “NO SIG-
NAL” will be displayed. When a sig-
nal that the projector is not preset to
receive is received, “NOT REG.” will
be displayed.
nal that the projector is not preset to
receive is received, “NOT REG.” will
be displayed.
About the INPUT modes
Used for projecting im-
ages from equipment
connected to INPUT 1
terminals.
ages from equipment
connected to INPUT 1
terminals.
Used for projecting im-
ages from equipment
connected to INPUT 2
terminal.
ages from equipment
connected to INPUT 2
terminal.
Used for projecting im-
ages from equipment
connected to INPUT 3
terminal.
ages from equipment
connected to INPUT 3
terminal.
Used for projecting im-
ages from equipment
connected to INPUT 4
terminal.
ages from equipment
connected to INPUT 4
terminal.
Used for projecting
images from equipment
connected to DIGITAL
INPUT terminal.
images from equipment
connected to DIGITAL
INPUT terminal.
INPUT 1
(Compo-
nent)
(Compo-
nent)
INPUT 2
(Compo-
nent/RGB)
(Compo-
nent/RGB)
INPUT 3
(S-Video)
(S-Video)
INPUT 4
(Video)
(Video)
DIGITAL
On-screen Display
Selecting the On-
screen Display Lan-
guage
screen Display Lan-
guage
English is the preset language for the On-
screen Display; however, this can be changed
to German, Spanish, Dutch, French, Italian,
Swedish, Portuguese, Chinese, Korean or
Japanese.
screen Display; however, this can be changed
to German, Spanish, Dutch, French, Italian,
Swedish, Portuguese, Chinese, Korean or
Japanese.
Display the “Language” menu and se-
lect the desired Language.
➝For operating the menu screen, see
pages 38 to 41.
lect the desired Language.
➝For operating the menu screen, see
pages 38 to 41.
INPUT 1 Mode
INPUT 2 Mode
INPUT 3 Mode
INPUT 4 Mode
DIGITAL INPUT Mode
"On-screen Display (Example)
XV_Z200E_E_p29_43.p65
03.10.30, 13:14PM
31
-32
-32
Image Projection
Turning the Power off
1
Press
on the remote con-
trol or
on the projector,
then press
or
again
while the confirmation message
is displayed, to put the projec-
tor into the standby mode.
is displayed, to put the projec-
tor into the standby mode.
• A dimly-lit screen is displayed for a
short time to reduce lamp damage.
Note
• If you accidentally pressed
and do not want to put the projector
into the standby mode, wait until the
confirmation message disappears.
into the standby mode, wait until the
confirmation message disappears.
2
Unplug the power cord from the
AC outlet after the cooling fan
stops.
AC outlet after the cooling fan
stops.
Info
• Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
tion. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
• When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment con-
nected first and then to the projec-
tor.
the power to the equipment con-
nected first and then to the projec-
tor.
STANDBY button
STANDBY button
XV_Z200E_E_p29_43.p65
03.10.30, 13:14PM
32