Read Sharp XV-Z10E (serv.man28) User Guide / Operation Manual online
Introduction
-7
Be sure to read the following safeguards when setting up
your projector.
your projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, con-
tact your nearest Sharp Authorised Pro-
jector Dealer or Service Centre for a re-
placement.
See “Replacing the Lamp” on page 54.
tact your nearest Sharp Authorised Pro-
jector Dealer or Service Centre for a re-
placement.
See “Replacing the Lamp” on page 54.
Caution concerning the setup of the projector
■ For minimal servicing and to maintain high image quality,
SHARP recommends that this projector be installed in an
area free from humidity, dust and cigarette smoke. When
the projector is subjected to these environments, the lens
and part of filter must be cleaned more often than usual.
As long as the projector is properly maintained in this man-
ner, use in these environments will not reduce the overall
operation life. Please note that all internal cleaning must
be performed by a Sharp Authorised Projector Dealer or
Service Centre.
area free from humidity, dust and cigarette smoke. When
the projector is subjected to these environments, the lens
and part of filter must be cleaned more often than usual.
As long as the projector is properly maintained in this man-
ner, use in these environments will not reduce the overall
operation life. Please note that all internal cleaning must
be performed by a Sharp Authorised Projector Dealer or
Service Centre.
Do not set up the projector in places exposed to
direct sunlight or bright light.
direct sunlight or bright light.
■ Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes out
the colours, making viewing difficult. Close the curtains and
dim the lights when setting up the screen in a sunny or
bright room.
the colours, making viewing difficult. Close the curtains and
dim the lights when setting up the screen in a sunny or
bright room.
The projector may be safely tilted to a maximum
angle of 12 degrees.
angle of 12 degrees.
■ Placement should be within ±12 degrees of horizontal.
Do not subject the projector to hard impact and/or vibration.
■ Take care with the lens so as not to hit or damage the
■ Take care with the lens so as not to hit or damage the
surface of the lens.
Do not mount the projector on a ceiling by turning it over.
■ Use the lens shift feature when projecting the image from
■ Use the lens shift feature when projecting the image from
a high position.
Rest your eyes occasionally.
■ Continuously watching the screen for long hours will cause
■ Continuously watching the screen for long hours will cause
eye strain. Be sure to occasionally rest your eyes.
Avoid locations with extremes of temperature.
■ The operating temperature of the projector is from +5°C to
■ The operating temperature of the projector is from +5°C to
+35
°C.
■ The storage temperature of the projector is from
–20
°C to +60°C.
Do not block the exhaust and intake vents.
■ Allow at least 20 cm of space between the exhaust vent
and the nearest wall or obstruction.
■ Be sure that the intake vent and the exhaust vent are not
obstructed.
■ If the cooling fan becomes obstructed, a protection circuit
will automatically put the projector into the standby mode.
This does not indicate a malfunction. Remove the projec-
tor power cord from the wall outlet and wait at least 10
minutes. Place the projector where the intake and exhaust
vents are not blocked, plug the power cord back in and
turn on the projector. This will return the projector to the
normal operating condition.
This does not indicate a malfunction. Remove the projec-
tor power cord from the wall outlet and wait at least 10
minutes. Place the projector where the intake and exhaust
vents are not blocked, plug the power cord back in and
turn on the projector. This will return the projector to the
normal operating condition.
Caution regarding transportation of the projector
■ When transporting the projector, be sure not to subject it
to hard impact and/or vibration, as this can result in dam-
age. Take extra care with the lens. Before moving the pro-
jector, be sure to unplug the power cord from the wall out-
let, and disconnect any other cables connected to it.
age. Take extra care with the lens. Before moving the pro-
jector, be sure to unplug the power cord from the wall out-
let, and disconnect any other cables connected to it.
■ Do not carry the projector by holding the lens.
■ When transporting the projector, be sure to attach the lens
shipping block and the lens cap to the projector.
Other connected equipment
■ When connecting a computer or other audio-visual equip-
ment to the projector, make the connections AFTER un-
plugging the power cord of the projector from the wall out-
let and turning off the equipment to be connected.
plugging the power cord of the projector from the wall out-
let and turning off the equipment to be connected.
■ Please read the operation manuals of the projector and
the equipment to be connected for instructions on how to
make the connections.
make the connections.
Using the projector in other countries
■ The power supply voltage and the shape of the plug may
vary depending on the region or country you are using the
projector in. When using the projector overseas, be sure
to use an appropriate power cord for the country you are
in.
projector in. When using the projector overseas, be sure
to use an appropriate power cord for the country you are
in.
Temperature monitor function
■ If the projector starts to overheat due
to setup problems or blockage of the
air vents, “
air vents, “
” and “
” will
illuminate in the lower left corner of
the picture. If the temperature con-
tinues to rise, the lamp will turn off, the temperature warn-
ing indicator on the projector will blink, and after a 90-sec-
ond cooling-off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on page 52
the picture. If the temperature con-
tinues to rise, the lamp will turn off, the temperature warn-
ing indicator on the projector will blink, and after a 90-sec-
ond cooling-off period the projector will enter the standby
mode. Refer to “Maintenance Indicators” on page 52
for
details.
Info
• The cooling fan regulates the internal temperature, and its
performance is automatically controlled. The sound of the
fan may change during projector operation due to changes
in the fan speed. This does not indicate malfunction.
fan may change during projector operation due to changes
in the fan speed. This does not indicate malfunction.
• Do not unplug the power cord during projection or cooling
fan operation. This can cause damage due to rise in inter-
nal temperature, as the cooling fan also stops.
nal temperature, as the cooling fan also stops.
BQC-PGB10S//1
12
°
XV_Z10E_E_p01_07.p65
03.11.7, 4:13 PM
7
Click on the first or last page to see other XV-Z10E (serv.man28) service manuals if exist.