XG-C68X (serv.man4). Service Manual - Sharp Projector Service Manual (repair manual)

xg-c68x (serv.man4) service manual
Model
XG-C68X (serv.man4)
Pages
127
Size
25.7 MB
Type
PDF
Document
Service Manual
Brand
Device
Projector / Service Manual
File
xg-c68x-sm4.pdf
Date

Read Sharp XG-C68X (serv.man4) Service Manual online

XG-C58X
XG-C68X
SERVICE MANUAL
SERVICE-ANLEITUNG
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
MODELS
MODELLE
SHARP CORPORATION
Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen
Originalzustand  gebracht werden.  Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet
werden.
CONTENTS
»
SPECIFICATIONS ............................................. 2
»
IMPORTANT SERVICE SAFETY
NOTES (for USA) ............................................... 3
»
NOTE TO SERVICE PERSONNEL ................... 4
»
OPERATION MANUAL ...................................... 8
»
DIMENSIONS .................................................. 12
»
REMOVING OF MAJOR PARTS ..................... 13
»
RESETTING THE TOTAL LAMP TIMER ......... 15
»
THE OPTICAL UNIT OUTLINE ....................... 16
»
SOFTWARE UPDATE PROCEDURE ............. 20
»
ELECTRICAL ADJUSTMENT ........................... 24
»
TROUBLE SHOOTING TABLE ....................... 35
»
BLOCK DIAGRAM ......................................... 102
»
OVERALL WIRING DIAGRAM ...................... 104
»
DESCRIPTION OF SCHEMATIC DIAGRAM . 106
»
SCHEMATIC DIAGRAM ................................ 107
»
PRINTED WIRING BOARD ASSEMBLIES ... 156
»
PARTS LIST
Ë
ELECTRICAL PARTS ................................ 172
Ë
CABINET AND MECHANICAL PARTS ..... 190
Ë
ACCESSORIES PARTS ............................ 196
Ë
PACKING PARTS ...................................... 196
»
PACKING OF THE SET ................................. 197
Page
XG-C58X
XG-C68X
LCD PROJECTOR
LCD PROJEKTOR
INHALT
Seite
»
TECHNISCHE DATEN .................................... 53
»
HINWEISE FÜR DAS
WARTUNGSPERSONAL ................................ 54
»
BEDIENUNGSANLEITUNG ............................ 56
»
ABMESSUNGEN ............................................. 60
»
AUSBAU WICHTIGER TEILE ......................... 61
»
RÜCKSTELLUNG DES LAMPEN-TIMERS .... 63
»
KURZBSCHREIBUNG
DER OPTIK-EINHEIT ...................................... 64
»
SOFTWARE-AKTUALISIERUNGS-
VERFAHREN ................................................... 68
»
ELEKTRISCH EINSTELLUNG ........................ 72
»
FEHLERSUCHTABELLE ................................. 84
»
BLOCKSCHALTBILD ..................................... 102
»
GESAMTSCHALTPLAN ................................ 104
»
BESCHREIBUNG DES SCHEMATISCHEN .......
   SCHALTPLANS ............................................. 106
»
SCHEMATISCHEN SCHALTPLANS ............. 107
»
LEITERPLATTENEINHEITEN ....................... 156
»
ERSATZTEILLISTE
Ë
ELEKTRISCHE BAUTEILE ....................... 172
Ë
GEHÄUSE UND MECHANISCHE
BAUTEILE ................................................. 190
Ë
ZUBEHÖRTEILE ....................................... 196
Ë
VERPACKUNGSTEILE ............................. 196
»
VERPACKEN DES GERÄTS ......................... 197
S95N2XG-C58X/
2
XG-C58X
XG-C68X
Specifications
LCD Projector
XG-C58X/XG-C68X
NTSC 3.58/NTSC 4.43/PAL/PAL-M/PAL-N/PAL 60/SECAM/
DTV480I/DTV480P/DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I
LCD panel X 3, RGB optical shutter method
Panel size: 0.99" (25.1 mm) (15 [H] X 20 [W] mm)
No. of dots: 786,432 dots (1,024 [H] X 768 [V])
1–1.27 X zoom lens, F1.7–2.2, f = 36.5–46.3 mm
SHP 310 W (Lamp unit: AN-C55LP)
15-pin mini D-sub connector
Y: 1.0 Vp-p, sync negative, 75 
terminated
P
B
: 0.7 Vp-p, 75 
 terminated
P
R
: 0.7 Vp-p, 75 
 terminated
750 TV lines (DTV720P)
15-pin mini D-sub connector
RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 
 terminated
HORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 
terminated
4-pin mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 
 terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 
 terminated
4-pin B-type USB female connector
9-pin mini DIN connector
15–126 kHz
43–200 Hz*
12–230 MHz
ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 47 k
 (stereo)
3.0 W (monaural)
4 cm X 7 cm
AC 120–240 V
3.4 A
50/60 Hz
405 W (Standard mode)/320 W (Low power mode) with AC 120 V
390 W (Standard mode)/315 W (Low power mode) with AC 240 V
0.5 W (AC 120 V) – 0.9 W (AC 240 V) (When “Mntr.out/RS232” is set to “OFF”)
1,522 BTU/hour (Standard mode)/1,202 BTU/hour (Low power mode) with AC 120 V
1,465 BTU/hour (Standard mode)/1,183 BTU/hour (Low power mode) with AC 240 V
41
°
F to 95
°
F (+5
°
C to +35
°
C)
–4
°
F to 140
°
F (–20
°
C to +60
°
C)
Plastic
38 kHz
15
3
8
" X 3 
7
8
" X 11 
9
16
" (390 (W) X 99 (H) X 294 (D) mm) (main body only)
15
1
2
" X 4 
7
16
" X 11 
5
8
" (393 (W) X 114 (H) X 303 (D) mm) (including adjustment foot
and projecting parts)
11.5 lbs. (5.2 kg)
Remote control, Power cord for U.S. and Canada, etc., Power cord for Europe, except U.K., Power
cord for U.K. and Singapore, RGB cable, USB cable, DIN-D-sub RS-232C adaptor, Air filter, Lens
cap, Projector manual and technical reference CD-ROM, Quick guide label, Operation manual
Product type
Model
Video system
Display method
LCD panel
Standard lens
Projection lamp
Component input signal
(INPUT1/2)
Horizontal resolution
Computer RGB input signal
(INPUT 1/2)
Video input signal
(INPUT 3)
S-video input signal
(INPUT 4)
USB terminal
Computer control signal (RS-232C)
Horizontal frequency
Vertical frequency
Pixel clock
Audio input signal
Audio output
Speaker system
Rated voltage
Input current
Rated frequency
Power consumption
Power consumption (standby)
Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Replacement parts
* Temporary noise may be visible with vertical frequencies above 100Hz if OSD functions are activated.
As a part of policy of continuous improvement, SHARP reserves the right to make design and speci-
fication changes for product improvement without prior notice. The performance specification figures
indicated are nominal values of production units. There may be some deviations from these values in
individual units.
3
XG-C58X
XG-C68X
IMPORTANT SERVICE SAFETY NOTES (for USA)
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and servicing guidelines as follows:
WARNING
1. For continued safety,  no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE PROJECTOR:
(Fire & Shock Hazard)
Before returning the projector to the user,  perform
the following safety checks:
1. Inspect lead wires are not pinched between the
chassis and other metal parts of the projector.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
current leakage in the following manner:
»
Plug the AC cord directly into a 120-volt AC outlet,
(Do not use an isolation transformer for this test).
»
Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15
µ
F capacitor in parallel
between all exposed metal cabinet parts and earth
ground.
»
Use an AC voltmeter with sensitivity of 5000 ohm
per volt.,  or higher,  sensitivity to measure the AC
voltage drop across the resistor (See Diagram).
»
All checks must be repeated with the AC plug
connection reversed.  (If necessary,  a non-polarized
adapter plug must be used only for the purpose of
completing these checks.)
Any reading of 0.3 volts RMS (this corresponds to
0.2 milliamp. AC.) or more is excessive and indicates
a potential shock hazard which must be corrected
before returning the unit to the owner.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
Many electrical  and  mechanical parts in Projector have
special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
n e c e s s a r i l y   i n c r e a s e d   b y   u s i n g   r e p l a c e m e n t
components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified  by “
å
and  shaded  areas in the Replacement Parts Lists and
Schematic Diagrams.  For continued protection,
replacement parts must be identical to those used in
the original circuit.  The use of a substitute replacement
parts which do not have the same safety characteristics
as the factory recommended replacement parts shown
in this service manual, may create shock,  fire or other
hazards.
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques,
dans les projecteur à présentent des caractéristiques
spéciales relatives à la sécurité,  qui ne sont souvent
pas évidentes à vue.
Le degré de protection ne peut pas être nécessairement
augmentée en utilisant des pièces de remplacement
étalonnées pour haute tension, puissance,  etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel;
les pièces électriques qui présentent ces particularités
sont identifiées par la marque “
å
” et hachurées dans
la liste des pièces de remplacement et les diagrammes
schématiques.  Pour assurer la protection, ces pièces
doivent être identiques à  celles  utilisées dans le circuit
d’origine.  L’utilisation de pièces qui n’ont pas les mêmes
caractéristiques que les pièces recommandées par
l’usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies ou autres accidents.
WARNING: The bimetallic component has the primary
conductive side exposed. Be very careful in
handling this component when the power is on.
AVERTISSEMENT: La composante bimétallique dispose du
conducteur primaire dénudé. Faire
attention lors de la manipulation de cette
composante sous tension.
AC
VOLTMETER
1.5k ohm  (10W)
0.15
µ
F
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT  TO  KNOWN
EARTH GROUND 
4
XG-C58X
XG-C68X
NOTE POUR LE PERSONNEL
D’ENTRETIEN
 PRECAUTION POUR LES RADIATIONS UV
La source de lumière, la lampe métal halide,
dans le projecteur émet de petites quantités de
radiation UV.
EVITEZ TOUTE EXPOSITION DIRECTE
DES YEUX ET DE LA PEAU.
Pour votre sécurité, nous vous prions de respecter
les points suivants:
1. Toujours porter des lunettes de soleil lors d’un
entretien du projecteur
avec la lampe allumée
et le haut du coffret retiré.
2. Ne pas faire fonctionner la lampe à l’extérieur du
boîtier de lampe.
3. Ne pas faire fonctionner plus de 2 heures avec le
coffret retiré.
Précautions pour les radiations UV
et la lampe haute pression
1. To u j o u r s   d é b r a n c h e r   l a   f i c h e  A C   l o r s   d u
remplacement de la lampe.
2. Laisser l’unité refroidir pendant une heure avant de
procéder à l’entretien.
3. Ne remplacer qu’avec une lampe du même type.
Type AN-C55LP caractéristique 80V/310W.
4. La lampe émet de petites quantités de radiation UV-
éviter tout contact direct avec les yeux.
5. La lampe haute pression implique un risque
d’explosion. Toujours suivre les instructions
d’installation décrites ci-dessous et manipuler la
lampe avec soin.
NOTE TO SERVICE
PERSONNEL
 UV-RADIATION PRECAUTION
The light source,  metal halide lamp,  in the projector
emits small amounts of UV-Radiation.
AVOID DIRECT EYE AND SKIN EXPOSURE.
To ensure safety please adhere to the following:
1. Be sure to wear sun-glasses when servicing the
projector with the lamp
turned “on” and the top
enclosure removed.
2. Do not operate the lamp outside of the lamp housing.
3. Do not operate for more than 2 hours with the
enclosure removed.
UV-Radiation and High Pressure
Lamp Precautions
1. Be sure to disconnect the AC plug when replacing
the lamp.
2. Allow one hour for the unit to cool down before
servicing.
3. Replace only with same type lamp. Type AN-C55LP
rated 80V/310W.
4. The lamp emits small amounts of UV-Radiation,
avoid direct-eye contact.
5. The high pressure lamp involves a risk of explosion.
Be sure to follow installation instructions described
below and handle the lamp with care.
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
12345678901234567890123456789012123456789012345
Page of 127
Display

Download Sharp XG-C68X (serv.man4) Service Manual (Repair Manual)

Here you can read online and download Sharp XG-C68X (serv.man4) Service Manual in PDF. XG-C68X (serv.man4) service manual will guide through the process and help you recover, restore, fix, disassemble and repair Sharp XG-C68X (serv.man4) Projector. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.