View Sharp PG-MB60X Handy Guide online
4 Furzeground Way,
Please contact your account manager directly or telephone 0208 7342000
Please visit the following link -
Product warranty is offered on the terms specified in this policy, provided that:
(a) The product is serviced by the approved service company.
(b) Repairs or alterations have not been performed or attempted by unauthorised personnel.
(c) The product is of original design and specification.
(d) The product has been properly maintained and operated in accordance with the
(e) The product is within its stated warranty period.
(f) Proof of purchase is available on request.
(g) The fault has been caused by a genuine manufacturing defect.
The following items are not covered by the warranty. Any work carried out relating to these
items will be on a chargeable basis:
(a) Faults caused directly or indirectly by incorrect installation, maintenance or operation.
(b) Accidental damage, misuse, abuse or neglect.
(c) Alteration or repairs carried-out by person(s) not authorised by Sharp.
(d) General wear & tear.
(e) Internal cleaning & maintenance.
(f) Act of God, such as fire, flood, lightening etc.
(g) The supply of fraudulent or negligent information to the Help-Desk or service company.
(h) Cosmetic parts, including cabinet & exterior parts.
(i) Consumable items, including projector lamps & air filters.
(j) Cables (unless faulty-as-new).
(k) Fuses (unless related to an applicable fault).
(m) Use of the product in conjunction with other products or accessories not approved by
(n) Pixel failures within the specification of the product. (LCD & DMD panels)
(p) Installation and/or decommissioning (unless otherwise stated).
Product returned to the approved service company with no-fault-found, or is found to be
operating in accordance with its specification, will be subject to a handling charge.
Routine maintenance, such as external cleaning, replacement of air filters etc, should be
carried out at the intervals specified in the product operation manual by the reseller (or end-
user where applicable).
Where these products are used in dusty and/or smoky environments, then the frequency of
routine maintenance should be increased appropriately
Where periodic internal cleaning is required, this must only be carried out by qualified
UK; Republic of Ireland
The reseller should return the product to the approved service company at their cost. The
approved service company will repair and return to the reseller under warranty.
The end-user returns the faulty lamp and lamp warranty claim form (Provided with the
projector) to the approved service company who will inspect and replace under warranty.
Lancashire OL1 4ER
Tel: 0161 626 4067
Fax: 0161 627 1741
indicator will illuminate red, and the power will turn off. After the power has been turned
off, follow the procedures given below.
to blockage of the air vents, or the setting location,
“TEMP ” will blink in the lower left corner of the
picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator
will blink, the cooling fan will run for further 90
seconds, then the power will be shut off. After
“TEMP” appears, be sure to perform the following
will be displayed on the screen in yellow. When
the lamp life reaches 0%, “LAMP” will change to
red, the lamp will automatically turn off and then
the projector as well. At this time, the Lamp
Replacement Indicator will illuminate in red.
without replacing the lamp, the projector will not
projector to an
area with proper
to your nearest
Projector Dealer or
and intake vents
5% or less.
the lamp. Take the
projector to your
Projector Dealer or
Service Centre for
replacing the lamp
whether any of the ventilation holes are blocked and then try turning the power back on. Wait until
the projector has cooled down completely before plugging in the power cord and turning the power
back on. (At least 10 minutes.)
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate
in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace
the power cord in the AC outlet and then turn the power on again.
cooling fan is running. The cooling fan runs for about 90 seconds.
life becomes 5% or less, or when you notice a significant deterioration in the picture and colour
quality. The lamp life (percentage) can be checked with the on-screen display.
Authorised Projector Dealer or Service Centre.
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.
recommended that the lamp be replaced with a new one immediately, even if the lamp appears to
be operating normally.
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult with a doctor as soon as possible.
projector. In such a case, it is recommended you contact your nearest Sharp Authorised Projector
Dealer or Service Centre to remove the damaged lamp and assure safe operation.
hot and touching it can lead to burn or injury.
lamp unit to fully cool before removing the lamp unit.
Authorised Projector Dealer or Service Centre for repair. Purchase a replacement lamp
unit of type AN-MB70LP from your nearest Sharp Authorised Projector Dealer or Service
Centre. Then carefully change the lamp by following the instructions described in this
section. If you wish, you may have the lamp replaced at your nearest Sharp Authorised
Projector Dealer or Service Centre.