PG-M25XE (serv.man28). Introduction - Sharp Projector User Guide / Operation Manual

There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.

This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.

To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equip-
ment.

The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.

The exclamation point within a triangle is
intended to alert the user to the presence of
impor tant operating and maintenance
(servicing) instructions in the literature
accompanying the product.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the user will be required to correct the interference
at his own expense.

See bottom of actual set.

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.

This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.

U.S.A. ONLY

U.S.A. ONLY

U.S.A. ONLY

U.S.A. ONLY

The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During
normal operation, when turning the power off always use the POWER button on the projector or on the remote
control. Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD.
FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

See “Replacing the Lamp” on 

.

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of
these materials may be regulated due to environmental considerations. For disposal or recycling information,
please contact your local authorities or, if you are located in the United States of America, the Electronic Industries
Alliance: www.eiae.org .

PRECAUTIONS A OBSERVER LORS 
DU REMPLACEMENT DE LA LAMPE.

DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE RETIRER LES VIS.
L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD, ATTENDRE 1 HEURE
AVANT DE PROCEDER AU REMPLACEMENT DE LA LAMPE.
NE REMPLACER QUE PAR UNE LAMPE SHARP DE TYPE BQC-PGM20X//1.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES YEUX.
ETEINDRE LA LAMPE AVANT DE PROCEDER A L’ENTRETIEN.
LAMPE A MOYENNE PRESSION : RISQUE D’EXPLOSION. DANGER POTENTIEL
DE PARTICULES DE VERRE EN CAS D’ECLATEMENT DE LA LAMPE
A MANIPULER AVEC PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
 

BEFORE REMOVING THE SCREW, DISCONNECT POWER CORD.
HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.
REPLACE WITH SAME SHARP LAMP UNIT TYPE BQC-PGM20X//1 ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF LAMP BEFORE SERVICING.
MEDIUM PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL HAZARD OF GLASS
PARTICLES IF LAMP HAS RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.

LAMP REPLACEMENT CAUTION

“Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device”.

For GyroRemote unit (RRMCG1631CESA)
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This device operates in the frequency band of 49.82 to 49.90 MHz with RF output power of less than 30 MicroWatts
EIRP (Effective Isotropic Radiated Power).
Caution
Any changes made to this device not expressly approved by the manufacturer could void the users right to
operate this device.

U.S.A. ONLY

CANADA ONLY

• Superior image quality with Fujinon™ optical lens system.

• Newly developed DDR (Double Data Rate) chip eliminates Color Break-

• Newly developed 12° DMD™ chip provides significantly improved opti-

• A new optical engine creates a unique slim design and compact size

• Supports a refresh rate (vertical frequency) of up to 200 Hz and a wide

• Using 

# 1,200) resolution can be displayed with minimal distortion.

• Realizes vivid images using the latest high image quality circuitry.

• New I/P conversion algorithm enhances the performance of the motion detect I/P

Extensive improvements on the jagged edges or slanted lines in moving images.

• Contrast Control Dynamic Gamma

Improved contrast and natural color gradation by minimizing hue change.

• Color Management Function

Supports sRGB (color management).

• Noise Reduction

Allows for a clear image even with noisy source signals.

• New Edge Up-Scaling

Reduces jaggies and flickering when up-scaling edges of slanted lines, enabling sharper quality
images.

• Wireless presentations using a wireless LAN PC card.

This wireless LAN PC card complies with IEEE802.11b wireless LAN standards.
Computers with built-in wireless LAN PC cards that support this standard allow for wireless
connections.

Note

• A wireless connection with all IEEE802.11b compliant computers is not guaranteed.

You can expand your presentation efficiency through a wireless connection, for example, by projecting
computer images through a projector installed on the ceiling.

Effective presentations can now be achieved without having to reconnect data cables.

• PC-less presentations using a memory card.

Just by inserting an IC media (a memory card) such as CompactFlash in the projecter using a
PCMCIA card (Type 

II

) adapter, you can make presentations or auto demonstrations without a

computer.

Note

• For wireless presentations using the wireless LAN PC card, as well as PC-less presentations

using memory cards, please refer to the Wireless Reality software operation manual.

• Using the Gyro function, you can achieve more effective and advanced

• The crisp screen pointer gives your presentations a more intuitive touch.

• Using the multi-directional wireless remote control, your transmission