Read Sharp PG-F150X (serv.man5) User Guide / Operation Manual online
8
Observe the following safeguards when setting up your
projector.
projector.
Caution concerning the lamp unit
■ Potential hazard of glass par-
ticles if lamp ruptures. In case
of lamp rupture, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center for replacement.
See “Replacing the Lamp” on
page 50.
of lamp rupture, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center for replacement.
See “Replacing the Lamp” on
page 50.
Caution concerning the setup of the
projector
projector
■ For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from
humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more of-
ten. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
projector be installed in an area free from
humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more of-
ten. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
Do not set up the projector in places
exposed to direct sunlight or bright light.
exposed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (approx. 9 degrees) of the
adjustment foot.
adjustment foot.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in
a high position
a high position
■ When placing the projector in a high position,
make certain it is carefully secure to avoid
personal injury caused by the projector fall-
ing down.
personal injury caused by the projector fall-
ing down.
Do not subject the projector to hard
impact and/or vibration.
impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
breaks to rest your eyes.
Avoid locations with extremes of
temperature.
temperature.
■ The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
vents.
■ Allow at least 11
13
/
16
inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.
wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion. (See pages 48 and 49.) Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion. (See pages 48 and 49.) Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
■ After the projector is purchased, a faint smell
from the vent may appear when the power is
first turned on. This is normal and is not a
malfunction. It will disappear after the projec-
tor is used for a while.
first turned on. This is normal and is not a
malfunction. It will disappear after the projec-
tor is used for a while.
PGF150X_E_P06_09.p65
07.5.31, 6:23 PM
8
Click on the first or last page to see other PG-F150X (serv.man5) service manuals if exist.