PG-A20X (serv.man6) - Sharp Projector Service Manual (repair manual). Page 5

Read Sharp PG-A20X (serv.man6) Service Manual online

13
PG-A20X
RS-232C Specifications and Command Settings
Return code (
)
Response code format
Normal response
Problem response (communication error or incorrect command)
Command 4-digit
Parameter 4-digit
Command format
Return code (
0DH
)
Return code (
)
CONTROL CONTENTS
Standby
Power On
INPUT1
INPUT2
INPUT3
INPUT1 SIGNAL TYPE : AUTO 
INPUT1 SIGNAL TYPE : RGB
INPUT1 SIGNAL TYPE : COMPONENT
Lamp Usage Time (hour)
Remaining Lamp Life (Percentage)
Lamp Status
Unit Status
Model Name Check
AV Mute Off 
AV Mute On
Auto Sync Start
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
OK or ERR
0~9999
0~100
0:Off, 1:On, 2:Retry, 3:Waiting, 4:Lamp Error
0:Normal, 1:Temp High, 2:Fan Err,
4:Filter Cover Err, 8:Lamp Life 5% or less, 
16:Lamp Burnt-out, 32:Lamp Not Lit, 
64:Temp Abnormally High
PROJECTOR NAME
OK or ERR
OK or ERR
OK or ERR
P
P
I
I
I
I
I
I
T
T
T
T
T
I
I
A
O
O
R
V
V
A
A
A
L
L
L
A
N
M
M
D
W
W
G
E
E
S
S
S
T
T
P
B
A
B
B
J
R
R
B
D
D
I
I
I
T
L
S
N
M
K
K
S
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
_
0
1
1
1
2
0
1
2
1
1
1
1
1
0
1
1
COMMAND PARAMETER
RETURN
BUTTONS & REMOTE CONTROL KEY
PC control
A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,
sold separately) to the projector. (See page 
20
 for connection.)
Communication conditions
Set the serial port settings of the computer to match that of the table.
Signal format: Conforms to RS-232C standard.
Parity bit: None
Baud rate: 9,600 bps
Stop bit: 1 bit
Data length: 8 bits
Flow control: None
Basic format
Commands from the computer are sent in the following order: command, parameter, and return code. After
the projector processes the command from the computer, it sends a response code to the computer.
Info
When more than one code is being sent, send each command only after the response code for the previous
command from the projector is verified.
Note
When the projector is put into the standby mode, a message “Shutting Down. Please Wait.” is displayed for
about 20 seconds. At that time, if the “POWR_ _ _1” command is being sent, “ERR” will be returned and this
command is not received.
Commands
Example: When turning on the projector, make the following setting.
_
_
Projector
Computer
Note
If an underbar (_)  appears in the parameter column, enter a space. If an asterisk (*) appears, enter a
value in the range indicated in brackets under CONTROL CONTENTS.
Page of 6
Display

Click on the first or last page to see other PG-A20X (serv.man6) service manuals if exist.