Read Sharp MX-M950 / MX-MM1100 (serv.man37) Service Manual online
MX-M1100 ADJUSTMENTS 6 – 68
6)
Press [REPEAT] button, set the second adjustment pattern on
the document table, and perform the procedure 5) again.
the document table, and perform the procedure 5) again.
The target density setting level for each density level can be
checked.
Check that the setting levels are increased in sequence of B -
O. If there is no level change or the level change is reversed, it
is judges as abnormal.
In case of an abnormality, repeat the procedures.
checked.
Check that the setting levels are increased in sequence of B -
O. If there is no level change or the level change is reversed, it
is judges as abnormal.
In case of an abnormality, repeat the procedures.
7)
Press [OK] button.
The density and gradation of the adjustment pattern used in
the procedure 5) are set as the service target.
(How to set the service target to the same density and gra-
dation of the factory target)
NOTE:
This procedure must not be executed when the printer density
and gradation was adjusted with Sim. 67-25 to a unique printer
density and gradation requested by the user and it was regis-
tered as the service target with Sim. 67-27.
The density and gradation of the adjustment pattern used in
the procedure 5) are set as the service target.
(How to set the service target to the same density and gra-
dation of the factory target)
NOTE:
This procedure must not be executed when the printer density
and gradation was adjusted with Sim. 67-25 to a unique printer
density and gradation requested by the user and it was regis-
tered as the service target with Sim. 67-27.
1)
Enter the Sim. 67-28 mode.
2)
Press [EXECUTE] button.
3)
Press [YES] button.
The service target is set to the same level of the factory target
printer density and gradation.
The service target is set to the same level of the factory target
printer density and gradation.
ADJ 13
Image send, FAX send mode
image quality adjustment
image quality adjustment
13-A
Color image send mode, image density and
gradation adjustment (by each mode)
gradation adjustment (by each mode)
Normally, there is no need to perform this adjustment. In the follow-
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When there is a defective copy in a scan image.
* When the scan image density is too light.
1)
ing cases, however, this adjustment must be performed.
* When the user requests to perform the adjustment.
* When there is a defective copy in a scan image.
* When the scan image density is too light.
1)
Enter the Sim. 46-4 mode.
2)
Select a mode to be adjusted with the scroll button.
3)
Enter the adjustment value with 10-key, and press [OK] button.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
When the adjustment value is increased, the image density is
increased. When the adjustment value is decreased, the
image density is decreased.
4)
Scan the color document in the color scan mode (Scan to PC
or Scan to e-Mail), and check the density of the received
image.
Check can be made also in the copy mode by the following
procedure. The scanned image, however, is in monochrome.
4) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
or Scan to e-Mail), and check the density of the received
image.
Check can be made also in the copy mode by the following
procedure. The scanned image, however, is in monochrome.
4) Press [CLOSE] button in the simulation mode to jump to the
normal copy mode, and make a copy and check the adjust-
ment result.
Switch alternatively between the simulation mode and the nor-
mal copy mode, and adjust and check the adjustment result
with an actual copy.
Repeat the procedures 3 and 4 until a satisfactory result is
obtained.
OK
SIMULATION NO.67-27
TEST
SCANNER TARGET OF PRINTER COLOR CALIB SETUP㧦SERVICE
BASE:8800
#B:
227, #C
624, #D:
908, #E:
1249, #F:
2074
#L: 184155, #M: 189254, #N: 194377, #:O: 197276
#G:
3298, #H: 18951, #I: 76117, #J: 128495, #K: 165225
1/1
0
CLOSE
REPEAT
0
SIMULATION NO.67̆28
TEST
STANDARD SCANNER TARGET OF PRINTER COLOR CALIB㧦SERVICE
CLOSE
EXECUTE
ARE YOU SURE?
YES
NO
Display/Item
Content
Setting range
Default
A
TEXT
Text mode
1 - 99
50
B
TEXT/PRINTED
PHOTO
PHOTO
Text/Printed Photo
mode
mode
1 - 99
50
C
TEXT/PHOTO
Text/Photograph
mode
mode
1 - 99
50
D
PRINTED
PHOTO
PHOTO
Printed Photo mode
1 - 99
50
E
PHOTOGRAPH
Photograph mode
1 - 99
50
F
MAP
Map mode
1 - 99
50
OK
A㧦 50
㧧
TEXT
B㧦 50
㧧
TEXT/PRINTED PHOTO
C㧦 50
㧧
TEXT/PHOTO
D㧦 50
㧧
PRINTED PHOTO
0
A:
SIMULATION NO.46㧙04
EXPOSURE ADJUSTMENT(COLOR)[SCANNER]
50
㨇
1 㨪 99 㨉
TEST
CLOSE
E㧦 50
㧧
PHOTOGRAPH
F㧦 50
㧧
MAP
Click on the first or last page to see other MX-M950 / MX-MM1100 (serv.man37) service manuals if exist.