Read Sharp MX-M904 / MX-M1204 (serv.man50) Technical Bulletin online
Sharp Electronics (UK) Ltd., Technical Services Group
[Description]
No.
Item
Details
1
Main unit control
Modification of a failure to restart the unit properly while acquiring the image (snapshot)
during the firmware upgrade due to lack of some data necessary.
during the firmware upgrade due to lack of some data necessary.
2
Main unit control
Modification of a problem which occurs with following steps: 1) Print out a test pattern in
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
3
Main unit control
Modification of Scan job which keep remaining internally. The problem occurs if Eco scan
setting was enabled but canceled after previewing for Copy job.
setting was enabled but canceled after previewing for Copy job.
4
Main unit control
Modification of the problems that FAX receiving may stop after reaching to the preset limit
or the job may disappear when printing because the internal processing at the time of job
completion cannot work correctly.
or the job may disappear when printing because the internal processing at the time of job
completion cannot work correctly.
5
Main unit control
Modification of L8-20 which may occur when condition signaling between internal modules
is not done properly.
is not done properly.
6
Main unit control
Modification of a failure to complete Fax firmware upgrade during firmware upgrade
7
Main unit control
Correction of slower performance during batch printing while MFP is in vendor mode.
8
Main unit control
Correction of the problem that the trimmer function of Copy mode becomes unavailable
when using the account application.
when using the account application.
9
UI
Modification of a failure to delete the job completed from Job Status (Direct print from USB
flash drive). User cannot delete the job on the Job Status screen.
flash drive). User cannot delete the job on the Job Status screen.
10 UI
Modification of a problem with "Automatically print stored jobs after login" in User Control
which is disabled while external authentication for OSA is enabled.
which is disabled while external authentication for OSA is enabled.
11 Network
Modification of different Fax event notification between OSA4.5 and OSA4.1
12 Network
The modification of garbled images which appear while the data communication speed of
a device is 10 Mbps.
a device is 10 Mbps.
13 Network
Modification of a communication error which occurs in case the devices with different MAC
address share same IP address (i.e. load balancer is installed).
address share same IP address (i.e. load balancer is installed).
14 Network
Modification of machine lockup (ex. operation panel does not function) due to the
unauthorized memory access caused by defective internal management processing in
WSD module.
unauthorized memory access caused by defective internal management processing in
WSD module.
15 Network
Correction of the problem that the machine locks up when accessing the specific MIB with
the undefined INDEX.
the undefined INDEX.
16 Network
Modification of an error to authenticate IEEE802.1X for wired LAN
17 Network
Modification of network lockup which occurs during the port scan on tandem port.
18 Network
Enabling display of Machine ID information in MIB
19 Network
Factory default of LPD timeout period is changed from 0 (infinite) to 90 sec.
*The value above will not be changed when updating the firmware in the field.
*The value above will not be changed when updating the firmware in the field.
20 Network
Modification is made so that prompt authentication by a login user is enabled/disabled in
Soft SW.
SIM55-3 SW No.24 Data3
0: Enabled (Default for all destinations other than Europe)
1: Disabled
Soft SW.
SIM55-3 SW No.24 Data3
0: Enabled (Default for all destinations other than Europe)
1: Disabled
21 Printer
Correction of the problem that the data may be printed in solid black if the processing of
CMYK 8bit expansion and the processing of halftone process control are performed
simultaneously.
CMYK 8bit expansion and the processing of halftone process control are performed
simultaneously.
22 Printer
When reprinting the print job with the combination of the mixed original and Z-Fold, the job
will be printed out with Z-Fold being cancelled. This problem has been corrected.
will be printed out with Z-Fold being cancelled. This problem has been corrected.
23 Printer
Correction of the problem that the performance may be slowing down in the process of
continuous printing.
continuous printing.
24 Printer
Modification of print operation which may stop displaying "Rendering" during mass
printing.
printing.
25 Printer
Correction of the problem that the separator page cannot be output when changing the
Click on the first or last page to see other MX-M904 / MX-M1204 (serv.man50) service manuals if exist.