Read Sharp MX-M850 (serv.man40) Service Manual online
MX-M1100 ROM VERSION-UP 10 – 2
3)
Current version number and the version number to be updated
will be shown for each firmware respectively.
Following key-codes will be changed;
NOW
will be shown for each firmware respectively.
Following key-codes will be changed;
NOW
→ CURRENT
NEXT
→ UPDATED TO
4)
Select the button of the firmware to be updated. The button will
be highlighted. (In this screen, [ICU(MAIN)] and [LANGUAGE]
are selected.) At the same time, [EXECUTE] button appears.
* Press the selected button again to release the selection.
* Press [ALL] button to select all items.
be highlighted. (In this screen, [ICU(MAIN)] and [LANGUAGE]
are selected.) At the same time, [EXECUTE] button appears.
* Press the selected button again to release the selection.
* Press [ALL] button to select all items.
5)
Press [EXECUTE] button. “ARE YOU SURE? [YES] [NO]”
appears on display. If no button is selected, [EXECUTE] button
is grayed out and cannot be pressed. Press [YES] to start the
update.
appears on display. If no button is selected, [EXECUTE] button
is grayed out and cannot be pressed. Press [YES] to start the
update.
6)
At the completion of the upgrade, the display will change to:
"COMPLETE: PLEASE TOUCH [OK] TO FINISH" Press OK.
The Imager will reboot at this time.
"COMPLETE: PLEASE TOUCH [OK] TO FINISH" Press OK.
The Imager will reboot at this time.
7)
Go to Simulation 22-05 and confirm the firmware has
upgraded successfully.
Note: If the Imager locks up or loses power during the
upgrade, it could corrupt the firmware, preventing the
imager from booting up normally. If this occurs, you can
"rescue" the firmware using the following procedure:
• Rename the firmware file on the USB device to emup-
upgraded successfully.
Note: If the Imager locks up or loses power during the
upgrade, it could corrupt the firmware, preventing the
imager from booting up normally. If this occurs, you can
"rescue" the firmware using the following procedure:
• Rename the firmware file on the USB device to emup-
date.sfu
• Power off the imager (both switches) and insert the USB
device (Jumpdrive) into the USB port of the imager.
• Power on the imager
• The Imager will boot up into emergency update mode.
• The Imager will boot up into emergency update mode.
When finished, the display will read "update completed"
• Power off the imager, and remove the USB device
• Reboot the imager, and go simulation 22-05 to confirm
• Reboot the imager, and go simulation 22-05 to confirm
firmware has upgraded successfully.
CLOSE
SIMULATION NO.49-01
TEST
FIRMWARE UPDATE
ICU(MAIN)
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
1/3
ICU(BOOTM)
CURRENT 09.00.00.00
UPDATED TO 01.00.00.00
:
ICU(BOOTS)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
LANGUAGE
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
GRAPHIC
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
SLIST
CURRENT 09.00.00.00
UPDATED TO 01.00.00.00
:
PCU(BOOT)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
PCU(MAIN)
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
DESK(BOOT)
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
A4LCC(BOOT)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
DESK(MAIN)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
CONFIG
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
ARE YOU SURE?
YES
NO
EXECUTE
ALL
CLOSE
SIMULATION NO.49-01
TEST
FIRMWARE UPDATE
ICU(MAIN)
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
1/3
ICU(BOOTM)
CURRENT 09.00.00.00
UPDATED TO 01.00.00.00
:
ICU(BOOTS)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
LANGUAGE
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
GRAPHIC
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
SLIST
CURRENT 09.00.00.00
UPDATED TO 01.00.00.00
:
PCU(BOOT)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
PCU(MAIN)
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
DESK(BOOT)
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
A4LCC(BOOT)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
DESK(MAIN)
CURRENT 01.01.00.00
UPDATED TO 09.00.00.00
:
CONFIG
CURRENT 01.00.00.00
UPDATED TO 01.01.00.00
:
ARE YOU SURE?
YES
NO
EXECUTE
ALL
COMPLETE㧦PLEASE TURN MAIN POWER OFF THEN ON
SIMULATION NO.49-01
TEST
FIRMWARE UPDATE
CLOSE
S
E
CAUTION DO NOT POWER OFF THE MFP! FIRMWARE UPDATE IN PROGRESS!
COMPLETE : PLEASE TOUCH [OK] TO FINISH.
SIMULATION NO.49-01
TEST
FIRMWARE UPDATE
CLOSE
OK
ERROR
: PLEASE TOUCH [OK] TO FINISH.
SIMULATION NO.49-01
TEST
FIRMWARE UPDATE
CLOSE
ICUM,PCU,SCU
OK
Click on the first or last page to see other MX-M850 (serv.man40) service manuals if exist.