Read Sharp MX-M623U / MX-M753U (serv.man6) Handy Guide online
Repair Hints
General Specification:
Enable Remote Operation
Panel, in order to connect to
the MFP using VNC?
Panel, in order to connect to
the MFP using VNC?
To enable the MFP to allow remote access/operation using VNC, select the
following menu:-
System Settings - Operation Settings.
Change the Operational Authority for Remote Software Operation to "Allowed".
If you wish to connect without accepting the remote connection from the MFP
Operation Panel, enable Operation from Specified PC. Enter the IP Address of the
Host PC into the "Operation from Specified PC" field.
following menu:-
System Settings - Operation Settings.
Change the Operational Authority for Remote Software Operation to "Allowed".
If you wish to connect without accepting the remote connection from the MFP
Operation Panel, enable Operation from Specified PC. Enter the IP Address of the
Host PC into the "Operation from Specified PC" field.
USB Port:
Changing The USB Port From
Front To Rear
Front To Rear
Changing The Dip Switches On The MFP Allows You To Activate The Front Or
Rear USB Ports
SW1 Off (UP) & SW2 ON (Down) – Rear USB Port Only
SW1 OFF (UP) & SW2 OFF (UP) – Front USB Port Only
Rear USB Ports
SW1 Off (UP) & SW2 ON (Down) – Rear USB Port Only
SW1 OFF (UP) & SW2 OFF (UP) – Front USB Port Only
SHARP OSA:
Is it possible to activate a trial
mode for Sharp OSA?
mode for Sharp OSA?
Sharp OSA trial mode that supports most functions can be
enabled by executing Sim 26-74
(restricted to approx 18000 pages, including
print/scan/copy/image send)
Note: Metadata & Open USB is not supported in Trial Mode.
enabled by executing Sim 26-74
(restricted to approx 18000 pages, including
print/scan/copy/image send)
Note: Metadata & Open USB is not supported in Trial Mode.
Facsimile
Is it possible to extend the
Retry Timer for FAX send?
Retry Timer for FAX send?
You can extend the FAX retry timer from the default 45 seconds to 60 seconds
(maximum) by changing the T0 timer within the following soft switch control:-
SIM 66-01: SW25, bit 1,2,3
Default:001 (45 sec) - > 010 (60 sec : Max 60 sec)
(maximum) by changing the T0 timer within the following soft switch control:-
SIM 66-01: SW25, bit 1,2,3
Default:001 (45 sec) - > 010 (60 sec : Max 60 sec)
MXKBX2 KEYBOARD
The external keyboard does
not function (i.e. no keyboard
input) after installation
not function (i.e. no keyboard
input) after installation
For the external keyboard unit and both USB ports to function correctly, the
USB Port DIP switch control on the MFP PWB must be set as follows:-
SW1 = OFF, SW2 = OFF (Front USB Port)
USB Port DIP switch control on the MFP PWB must be set as follows:-
SW1 = OFF, SW2 = OFF (Front USB Port)
When using the external
keyboard unit, the @
symbol/key is entered as “
when using direct address
entry (E-Mail address)
keyboard unit, the @
symbol/key is entered as “
when using direct address
entry (E-Mail address)
After installing the MXKBX2 keyboard unit, ensure to configure the correct
keyboard language.
Enter [System Settings] – [Keyboard Select] menu and set the keyboard
language to English (US)
keyboard language.
Enter [System Settings] – [Keyboard Select] menu and set the keyboard
language to English (US)
SHARPDESK
Corrupt image output when
printing a Word Document
containing an image
printing a Word Document
containing an image
Click on the first or last page to see other MX-M623U / MX-M753U (serv.man6) service manuals if exist.