Read Sharp MX-M364N / MX-565N Handy Guide online
Test Simulation
SHARP
Document Solution Centre
41
24
Data Counter & Clear
1
Jam/trouble counter clear
2
Paper feed counter clear
3
Document feed & output counter clear
4
Maintenance counter clear
5
Developer counter clear
6
Copy Counter clear
9
Print & other counter clear
10 Fax counter clear
12 Document filing counter clear
15 Network scanner counter clear
25 Toner usage estimator counter clear
35 Toner cartridge use status clear
12 Document filing counter clear
15 Network scanner counter clear
25 Toner usage estimator counter clear
35 Toner cartridge use status clear
25
DV Auto Adjustment & Monitor
1
Toner sensor monitor (Process drive)
2
Auto developer adjustment setting
4
Toner supply quantity data display
26
Device Configuration
1
Right Tray setup
2
LCC paper size setup
3
Auditor setup
5
A3 Total/Maintenance counter set-up
6
Destination set-up
7
Machine ID setting
8
Long paper mode counter setting
10 Network scan trial mode set-up (MX-AMX1)
18 Toner save operation
30 CE mark control setup
32 Fusing cleaning operation setting
35 Trouble memory mode setting
38 Engine life over setting (Maintenance)
41 Pamphlet mode AMS operation
49 Copy speed mode setup (Postcard)
50 Function setting (B/W reverse, finisher)
51 Serial port operation setting (for PCI)
52 Blank paper count mode setting (non
18 Toner save operation
30 CE mark control setup
32 Fusing cleaning operation setting
35 Trouble memory mode setting
38 Engine life over setting (Maintenance)
41 Pamphlet mode AMS operation
49 Copy speed mode setup (Postcard)
50 Function setting (B/W reverse, finisher)
51 Serial port operation setting (for PCI)
52 Blank paper count mode setting (non
printed paper – insert/cover page)
53 Enable/Disable auto calibration (gradation
& density)
65 Finisher staple alarm mode set-up
69 Toner near end setting
71 Web browsing trial mode setup
73 Poster enlargement image loss adjustment
74 OSA trial mode setting
78 Remote operation (VNC) password setting.
79 User data delete pop up display
69 Toner near end setting
71 Web browsing trial mode setup
73 Poster enlargement image loss adjustment
74 OSA trial mode setting
78 Remote operation (VNC) password setting.
79 User data delete pop up display
enable/disable
30
Sensor Operation & Test
1
Main unit sensor check
2
Paper feed sensor check (main body)
40
Bypass Operation & Adjustment
2
Bypass tray width adjustment
7
Bypass tray width detection manual setting
41
OSS Operation & Adjustment
1
Document sensor operation check
2
Document sensor output setup
3
Document sensor output display
43
Fuser Setting & Adjustment
1
Fuser temperature setup for each mode
2
Fusing operation and preheating setup
20 Fuser temperature. correction for low
temperature & humidity (L/L)
21 Fuser temp correction for high
temperature & humidity (H/H)
24 Fuser temperature correction setting
31 Fuser web operation check
32 Force operation of web cleaning (job end)
34 Fusing lower web cleaning motor operation
35 Fusing NIP operation check
31 Fuser web operation check
32 Force operation of web cleaning (job end)
34 Fusing lower web cleaning motor operation
35 Fusing NIP operation check
44
Process Control Data
1
Process control mode setting
2
Process control sensitivity adjustment
4
Process control initial density setup
6
High density process control correction
9
Process control data display
12 DM data, patch/base data display
14 Fuser temp.& humidity output data
15 OPC drum idle rotation setting
17 Process refresh execution
21 Half tone process control registration
22 Half tone process control patch result
24 Half tone correction data result display
25 Initial half tone correction data display
26 Half tone process control execution
27 Half tone process control correction clear
28 Process control timing (On/Off) setting
29 Enable/disable half tone correction (Job)
34 Process control execution setting
37 DV bias correction level setting for
14 Fuser temp.& humidity output data
15 OPC drum idle rotation setting
17 Process refresh execution
21 Half tone process control registration
22 Half tone process control patch result
24 Half tone correction data result display
25 Initial half tone correction data display
26 Half tone process control execution
27 Half tone process control correction clear
28 Process control timing (On/Off) setting
29 Enable/disable half tone correction (Job)
34 Process control execution setting
37 DV bias correction level setting for
continuous print mode.
43 DV unit installation identification check
Click on the first or last page to see other MX-M364N / MX-565N service manuals if exist.