Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online
MX-M565N ADJUSTMENTS AND SETTINGS 4 – 31
NOTE: Since the SIT chart (UKOG-0280FCZZ or UKOG-0280FC
Z1) is easily discolored by sunlight (especially ultraviolet
rays) and humidity and temperature, put it in a bag (such
as a dark file) and store in a dark place of low temperature
and low humidity.
rays) and humidity and temperature, put it in a bag (such
as a dark file) and store in a dark place of low temperature
and low humidity.
11-A
(2)
Shading adjustment (Calibration) (DSPF
mode)
Shading adjustment (Calibration) (DSPF
mode)
(1) Note before adjustment
1)
Check to insure that there is no dirt or dust on the DSPF scan-
ning glass, the mirror, and the lens surface. (If there is, clean it
with alcohol.)
ning glass, the mirror, and the lens surface. (If there is, clean it
with alcohol.)
2)
Open the DSPF document scanning section, insert the shad-
ing adjustment sheet (UKOG-0333FCZZ), and close the DSPF
document scanning section.
ing adjustment sheet (UKOG-0333FCZZ), and close the DSPF
document scanning section.
* When inserting the shading adjustment sheet, insert it along
the rear edge frame so that the rear edge of the shading
adjustment sheet comes to the root of the actuator.
adjustment sheet comes to the root of the actuator.
3)
Enter the SIM 63-2 mode.
4)
Select [DSPF SHADING].
5)
Press [EXECUTE] key. (The shading adjustment process is
started.)
started.)
* The shading adjustment sheet is transported by about
25mm, and shading data are obtained during transport.
* During shading adjustment, "SHADING EXECUTING..." is
displayed.
* When [EXECUTE] key is pressed during shading adjust-
ment, the operation is interrupted.
* When shading adjustment is completed normally, [EXE-
CUTE] key returns to the normal display and "COMPLETE"
is displayed.
is displayed.
<Descriptions of keys>
<Result display>
11-A
(3)
CCD gamma adjustment (CCD calibration)
(DSPF mode)
CCD gamma adjustment (CCD calibration)
(DSPF mode)
This adjustment is required in the following cases:
* When the DSPF CCD unit is replaced.
* When a U2 trouble occurs.
* When the DSPF control PWB is replaced.
* When the EEPROM on the scanner control PWB is replaced.
(1) Note before adjustment
1)
Check to insure that there is no dirt or dust on the DSPF scan-
ning glass, the mirror, and the lens surface. (If there is, clean it
with alcohol.)
ning glass, the mirror, and the lens surface. (If there is, clean it
with alcohol.)
2)
Check to confirm that the patches in BK1 and BK2 arrays of
the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1) are
free from dirt and scratches. If they are dirty, clean them. If
they are scratched or streaked, replace with new one.
the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1) are
free from dirt and scratches. If they are dirty, clean them. If
they are scratched or streaked, replace with new one.
NOTE:
Since the SIT chart is easily discolored by sunlight (especially
ultraviolet rays) and humidity and temperature, put it in a bag
such as a clear file) and store in a dark place of low tempera-
ture and low humidity.
ultraviolet rays) and humidity and temperature, put it in a bag
such as a clear file) and store in a dark place of low tempera-
ture and low humidity.
Display
Content
OC
SHADING
SHADING
OC analog correction level correction, and shading
correction data making (Document table mode)
correction data making (Document table mode)
DSPF
SHADING
SHADING
DSPF analog correction level correction, and shading
correction data making (SPF mode)
correction data making (SPF mode)
Display
Content
COMPLETE
Normal completion
ERROR
Abnormal completion
INCOMPLETE
Incomplete, interruption
2
: ‘16/Jan
2
Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.