MX-M363N, MX-M363U, MX-M503N, MX-M503U (serv.man18). June 10 - Sharp Copying Equipment Service Manual (repair manual). Page 13

MX-M503N  MX-M283N/M363N/M363U/M453N/M453U/M503N/M503U/M282N/M362N/M452N/M502N  1 – 8

2)

Adjust the guide plates A and B by squeezing their lock levers
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.

Used to set the specifications with SIM26 according to the cus-
tomer's request.

To customize the following items after completion of the destination
setup, change the set values.

(Note)
Before checking the copy density and gradation, be sure to execute
the following jobs.
* Execute the high density image correction (Process correction)

forcibly. (SIM 44-6)

* Execute the half-tone image correction forcibly. (SIM 44-26)
(Method)
Make a copy of the gray test chart (UKOG-0162FCZZ), and check
that it is proper.
Note for checking the copy mode density
To check the density, use the gray test chart (UKOG-0162FCZZ).
Set the copy density level to "Manual 3" in the Text/Printed Photo
mode (Manual).
In addition, all the picture quality adjustment settings in the user
adjustment mode must be set to the default (center).
[Check with the gray test chart (UKOG-0162FCZZ)]
In the copy density check with the gray test chart, check to insure
the following conditions.

[Check with the servicing color test chart (UKOG-0317FCZZ/
UKOG-0317FC11 or UKOG-0326FCZZ/UKOG-0326FC11)]
Check to confirm that it is in the conditions shown below.

If no printer option is installed to the U model, the following proce-
dures are not required. (SIM64-5 does not operate.)
(Note)
Before checking the printer density and gradation, be sure to exe-
cute the following jobs.
* Execute the high density image correction (Process correction)

forcibly. (SIM 44-6)

* Execute the half-tone image correction forcibly. (SIM 44-26)
(Method 1)
Execute SIM 64-5 to print the print test pattern.
Set each set value to the default and press [EXECUTE] key. The
print test pattern is printed.

The print density must be changed gradually from the lighter level
to the darker level. The density changing direction must not be
reversed.
(Method 2)
Execute SIM 67-25 to print the adjustment check pattern.

The print density must be changed gradually from the lighter level
to the darker level. The density changing direction must not be
reversed.
Patch A or B is slightly copied.

26

6

Used to set the destination.

26

2

LCC paper size setting

3

Used to set the auditor specification mode.

5

Used to set the count mode of the total counter and the 
maintenance counter.

18

Used to set YES/NO of the toner save mode 
(Only in UK and Japan versions)
* For other destination versions, this setup is made by 

the user program.

52

Used to set YES/NO of counting when non-print paper 
is passed through each counter.

53

Used to set YES/NO of user calibration permission.

65

Used to set the limit number of sheets for stapling.

B

A

1

2

3

4

5

6

7

8

9

10

W

SHARP GRAY CHART

SHARP gray chart

Patch 1 is not copied.

Patch 2 is
slightly copied.

Patch 3 is copied.

Serviceman chart (Color patch section)

Patch 7 is slightly
copied or not copied.

Q (Max)

A B C D E F G H I J K L M N O P

Patch A or B is slightly copied.

High density

Low density

The patch density is identical between patches or not reversed.
The patch density is changed gradually.