MX-M283N (serv.man14). CCE-1309 REVISED BULLETIN FOR PHOTO SENSOR TROUBLE PLEASE READ NOTES MARKED IN RED FOR PART NUMBER CHANGES IN THIS BULLETIN - Sharp Copying Equipment Technical Bulletin (repair manual)

mx-m283n (serv.man14) technical bulletin
Model
MX-M283N (serv.man14)
Pages
5 Few pages! See other manuals at the bottom of the first or last page.
Size
632.99 KB
Type
PDF
Document
Technical Bulletin
Brand
Device
Copying Equipment / CCE-1309 REVISED BULLETIN FOR PHOTO SENSOR TROUBLE PLEASE READ NOTES MARKED IN RED FOR PART NUMBER CHANGES IN THIS BULLETIN
File
mx-m283n-sm14.pdf
Date

Read Sharp MX-M283N (serv.man14) Technical Bulletin online

 
                                        Sharp Electronics (UK) Ltd., Document Systems Support
 
 
 
 
 
1/5 
 
Date:  
 
12
th
 June 2015 
Model:   
 
See below 
Ref.:   
 
CCE 1309 
Colour:   
 
White 
Page: 
 
1 of 5 
TECHNICAL BULLETIN 
PHOTO SENSOR TROUBLE 
Please read notes highlighted in RED 
 
1. Model Name: 
MFP Main unit 
 
 
    MX-1810U/2010U/2010UX, MX-RP12, MX-2310U/3111U, MX-2614N/3114N 
 
 
    MX-2615N/3115N, MX-2610N/3110N/3610N, MX-2640N/3140N/3640N, MX-2314N 
 
 
    MX-4110N/4111N/4112N/5110N/5111N/5112N, MX-M283N/M363N/M453N/ M503N/ 
 
 
    MX-M363U/453U/503U 
 
 
Desk 
 
 
    MX-DE12/DE13/DE14/ DE20, MX-DE15/DE16, MX-DEX8/DEX9 
 
2. Symptom: 
Due to the reduction of the light amount from the photo sensor used for Paper Feed/Transport   
 
 
system and Drum phase detection, the following troubles have been observed 
 
 
(1) Paper Jam in the area around the paper feed section of the cassette ~ Transport section of   
 
 
      Desk/Main unit until PPD1, and also in Document Feeder) 
 
 
(2) “Close the right side cover.” message is not displayed. 
 
 
(3) “Add paper” message does not disappear or the paper cannot be lifted. 
 
 
(4) Drum phase sensor trouble “F2-50~53” occurs. 
 
3. Cause  
The light reduction at the photo sensor is attributed to a resin change during the production of the   
 
 
wafer of the LED chip. The characteristic of the light being received by the wafer is uneven and is   
 
 
out of specification. On the following two types of photo sensors in the list below, the resin which is   
 
 
used in molding the element (chip) was changed in the middle of production, and the defective   
 
 
chips were mixed with non-defective chips. The defective chips have a smaller opening in which   
 
 
light passes through and caused a reduction of light being received on the wafer of the sensors.   
 
 
The old style 1A and 1S type sensors have no markings on them and it is impossible to distinguish   
 
 
the good sensors from the defective ones. 
Type 
Parts Code 
Section to be used 
Remarks 
1A 
VHPGP
1A
73
A
+-18 
 
(New part number- 
VHPGP1A73AR-1)     
Used for the original 
feeding, paper 
feeding/transport 
system 
*Used with 10mA as the initial value of IF (forward 
current) and it is possible to use with up to 1mA 
when deteriorated. 
*Weak against Hot Swap, static electricity, 
high-voltage leakage. 
1S 
VHPGP
1S
73
P
+-18 
Used for Drum phase 
detection system, and 
also the original 
feeding, paper 
transport/paper feeding 
system.    Section to be 
used varies depending 
on the model. 
*Used with 20mA as the initial value of IF (forward 
current) and it is possible to use with up to 0.4mA 
when deteriorated. 
*Strong against Hot Swap, static electricity, 
high-voltage leakage. 
*Based on above, 1S type sensor has more margin 
than 1A type sensor, which takes longer time to 
failure. 
 
 
                                              Sharp Electronics (UK) Ltd., Document Systems Support
 
 
 
 
2/5 
 
 
Note) Identification of 1A type sensor and 1S type sensor 
 
 
            Shape of the connector differs between 1A type and 1S type. 
 
 
      (See the right photos) 
    1A type sensor 
 
    1S type sensor 
 
 
 
 
4. Item of change 
To prevent the light reduction at the photo sensor the photo sensor has been changed. 
 
 
1. Identification of Old/new photo sensor (1A type)   
 
 
    1) There is no marking or engraved mark on the old photo sensor.   
 
 
    2) A red marking is placed on the connector side and an engraved marking is on the opposite   
 
 
        side of the connector on the new photo sensor. 
 
 
          Marking on the connector   
Location where the marking is engraved 
 
 
 
 
 
 
2. Identification of old/new photo sensor (1S type)   
 
 
    1) No marking is engraved on the old photo sensor. 
 
 
    2) A marking is engraved both on the connector side and the opposite side on the new photo   
 
 
        sensor. 
 
 
        Location where the marking is engraved 
 
 
 
 
 
5. Field Action
      Please replace the photo sensor in advance, based on the specific production month 
 
 
  (see the following list) that the resin was changed and defective chips were mixed.   
Model 
Target Production Month 
MX-1810U/2010U/2010UX(MX-RP12) 
  From October 2012 production   
  to March 2013 production   
MX-2314N 
MX-2310U/3111U 
MX-2614N/3114N 
MX-2615N/3115N 
MX-2610N/3110N/3610N 
MX-2640N/3140N/3640N 
MX-4110N/4111N/4112N/5110N /5111N/5112N 
MX-M283N/M363N/M453N/M503N   
/M363U/453U/503U 
MX-DE12/DE13/DE14/ DE20 
MX-DE15/DE16 
MX-DEX8/DEX9 
 
 
For models other than above, please take action on an as-needed basis. 
6. Action 
 
1
A
 type: From mid-November 2013 production   
 
 
1
S
 type: From December 2013 production 
Example of engraved 
marking 
Example of engraved 
marking 
 
                                          Sharp Electronics (UK) Ltd., Document Systems Support
 
 
 
 
3/5 
Please Note when ordering VHPGP1A73A+-18 this will change to the new part number 
VHPGP1A73AR-1 Or use this new PN. When ordering. VHPGP1S73P+-18 remains the same. 
Please see parts action on page 5 of 5 
   
*Position where the photo sensor is used: 
 
 
    :(GP1
A
73A Type) 
 
        :(GP1
S
73P Type) 
 
    MX-1810U/2010U/2010UX, MX-RP12, MX-2310U/3111U, MX-2614N/3114N, MX-2610N/3110N/3610N 
    MX-2640N/3140N/3640N , MX-2314N 
    RSPF(REVERSING SINGLE PASS FEEDER) 
 
 
 
      Main unit 
 
 
 
 
 
 
 
 
Desk (MX-DE14) 
 
 
 
 
 
 
 
 
 
 
      Desk (MX-DE12)   
 
 
 
 
Desk (MX-DE20) 
 
 
 
 
 
 
 
 
      Desk (MX-DE13)   
 
 
 
 
 
 
 
 
 
 
 
 
 
*For detail, please see Parts Guide for the target model. 
 
 
 
                                              Sharp Electronics (UK) Ltd., Document Systems Support
 
 
 
 
4/5 
 
    MX-4110N/4111N/4112N/5110N /5111N/5112N 
      RSPF (REVERSING SINGLE PASS FEEDER) 
 
 
 
      DSPF (DUPLEX SINGLE PASS FEEDER) 
 
 
Desk (MX-DE16/DEX9) 
 
 
 
      Main unit 
 
 
 
 
 
 
 
 
 
 
 
Desk (MX-DE15/DEX8) 
 
 
 
 
 
 
 
 
      MX-M283N/M363N/M453N/M503N /M363U/453U/503U 
      RSPF (REVERSING SINGLE PASS FEEDER) 
 
      DSPF (DUPLEX SINGLE PASS FEEDER) 
 
 
 
      Main unit 
 
 
 
 
 
 
 
 
 
 
 
 
DPED2 
DLUD1 
DCSPD1 
DSW_DSK 
DPFD1 
DCSPD2 
DPED1 
DPFD2 
DLUD2 
DPED1 
DPFD1 
DSW_DSK 
DCSPD1 
DLUD1 
* For detail, please see Parts Guide for the target model. 
Page of 5
Display

Download Sharp MX-M283N (serv.man14) Technical Bulletin

Here you can read online and download Sharp MX-M283N (serv.man14) Technical Bulletin in PDF. MX-M283N (serv.man14) technical bulletin will guide through the process and help you recover, restore, fix, disassemble and repair Sharp MX-M283N (serv.man14) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.