Read Sharp MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man5) Handy Guide online
Test Simulations
24
Document Solutions After Sales Service
Main Sub Functions
66
7
Output all image data saved in the image memory.
8
Send the selected sound messages to the line and the speaker.
9
Send the selected sound message to the line and the speaker. (Send level: Soft
SW setting) * For details of sound messages, refer to the sound message table of
SIM66-08.FAX
SW setting) * For details of sound messages, refer to the sound message table of
SIM66-08.FAX
10
Clear the FAX and image send image data.
11
Send the selected signal at 300bps to the line and the speaker.
12
Send the selected signal at 300bps to the line and the speaker. (Send level: Soft
SW setting) * For the kings of send signals at 300bps, refer to SIM66-11, 300bps
send signal table.
SW setting) * For the kings of send signals at 300bps, refer to SIM66-11, 300bps
send signal table.
13
Register dial numbers for SIM66-14/15/16, Dial test. (Up to 20 digits can be
registered.)
registered.)
14
Execute the dial pulse (10PPS) send test and to adjust the make time.
15
Execute the dial pulse (20PPS) send test and to adjust the make time.
16
Execute the DTFM signal send test and to adjust the send level.
17
Send the DTMF signal to the line and the speaker. (Send level: Max.)
18
Send the DTMF signal to the line and the speaker. (Send level: Soft SW setting)
21
Print the selected items (system error, protocol monitor).
22
Set the handset sound volume. (This simulation can be executed even though the
handset setting is set to NO. When, however, the handset is not installed, the
sound volume cannot be checked.) (Japan model only)FAX
handset setting is set to NO. When, however, the handset is not installed, the
sound volume cannot be checked.) (Japan model only)FAX
24
Clear the FAST save data.
29
Initialize the telephone book data (the one-touch registration table, the
FTP/Desktop expansion table, the group expansion table, the program registration
table, the interface memory box table, the meta data, Inbound Routing, and the
Document Admin table).
FTP/Desktop expansion table, the group expansion table, the program registration
table, the interface memory box table, the meta data, Inbound Routing, and the
Document Admin table).
30
Display the TEL/LIU status change, The display is highlighted by status change.
31
Set ON/OFF the port for output to TEL/LIU.
32
Check the fixed data received from the line and to display the result.
33
Execute detection of various signals with the line connected and to display the
detection result. When a signal is detected, the display is highlighted.
detection result. When a signal is detected, the display is highlighted.
34
Used to execute the send test and display the time required for sending image data
in the test. Used to execute send test and display. (Unit: ms)
in the test. Used to execute send test and display. (Unit: ms)
36
Check send and receive data from the MODEM controller to the MFP controller or
the data line or the command line individually.
the data line or the command line individually.
39
Check and change the destination setting saved in EEPROM of the FAX BOX.
42
Rewrite the program to power control installed in the FAX BOX.
43
Write the adjustment value into the power control installed in the FAX BOX.
61
Display the FAX-related soft SW (151 - 250) on the LCD to allow changing the soft
SW while checking with the LCD.
SW while checking with the LCD.
62
Import the FAX receive data into a USB memory in PDF file type.
67 17 Printer
reset.
45 Adjust
the
printer
image filter and trapping.
Click on the first or last page to see other MX-M264N / MX-M264NR / MX-M264NV / MX-M264U / MX-M314N / MX-M314NR / MX-M314NV / MX-M314U / MX-M354N / MX-M354NR / MX-M354U (serv.man5) service manuals if exist.