Read Sharp MX-FX10 Service Manual online
MX-FX10 TROUBLE CODE LIST 6-1
[6] TROUBLE CODE LIST
1. FAX-related service call error
2. Communication result code
Described on the communication report table, the communication man-
agement table, and the protocol communication report table when com-
munication is completed.
agement table, and the protocol communication report table when com-
munication is completed.
A. Composition of communication report code
Communication result X X (X X X X)
Upper 2 digits of a communication result code: Communication report
code of 00 - 90 (Refer to the list of communication report codes.)
code of 00 - 90 (Refer to the list of communication report codes.)
Lower 4 digits of a communication result code: Codes used by service-
man.
man.
Note) Communication report sub code 1 and sub code 2 are in hexadec-
imal. (The others are in decimal.)
< Communication result code list >
(Note) For result codes 16 - 31, V.34 mode communication.
For 32 or later, refer to the table below.
< Communication result code list >
MAIN
SUB
Conditions
F6
00
FAX board
c o m m u n i -
cation trou-
ble
c o m m u n i -
cation trou-
ble
When sending cannot be made due to
buffer over.
buffer over.
10
FA X h a r d
error
error
Wh en o n e of t h e fo llow i n g it em s i s
detected.
Page Memory Error/FAX Board Error/
ROM Error/RAM Error/Flash ROM Error.
detected.
Page Memory Error/FAX Board Error/
ROM Error/RAM Error/Flash ROM Error.
80
FAX break
error
error
When an error is detected in the IO ASIC
serial controller.
serial controller.
81
FAX parity
error
error
82
FA X o v e r -
run error
run error
84
FA X f r a m -
ing error
ing error
88
FA X i n t e r -
face error
face error
There is no response of data from the
machine for 30 sec or more.
machine for 30 sec or more.
97
C o m b i n a -
t i o n e r r o r
b e t w e e n
t h e FA X
unit and the
main unit
t i o n e r r o r
b e t w e e n
t h e FA X
unit and the
main unit
When this fax unit is installed to the
machine that can not install this.
machine that can not install this.
99
FA X l a n -
guage error
guage error
When the TEL/LIU PWB for EX Japan is
operated under the setting for Japan.
When the TEL/LIU PWB for Japan is
operated under the setting for EX Japan.
When this fax unit is installed to the
machine that can install only AR-FX11.
operated under the setting for Japan.
When the TEL/LIU PWB for Japan is
operated under the setting for EX Japan.
When this fax unit is installed to the
machine that can install only AR-FX11.
U1
03
FA X b a t -
tery error
tery error
When the battery voltage on the FAX
PWB falls.
PWB falls.
Top 2 digits
Communication report sub code 1 (Refer to
the list of communication sub code 1.)
the list of communication sub code 1.)
Bottom 2 digits
Communication report sub code 2 (Refer to
the list of communication sub code 2.)
the list of communication sub code 2.)
Result
code
Final reception signal
(Transmitting side)
Final reception signal
(Receiving side)
0
Abnormal signal
Abnormal signal
1
NSF, DIS
(SID), (SUB), NSS, DCS
2
CFR
(PWD), (SEP), NSC, DTC
3
FTT
EOP
4
MCF
EOM
5
PIP, PIN
MPS
6
RTN, RTP
PRI-Q
7
No signal, DCN
DCN
8
PPR
PPS-EOP
9
PPS-EOM
10
PPS-MPS, PPS-NULL
11
RNR
RR
12
CTR
CTC
13
ERR
EOR-Q
14
PPS-PRI-Q
15
16
Abnormal signal
Abnormal signal
17
NSF, DIS
SID, SUB, NSS, DCS
18
CFR
PWD, SEP, NSC, DTC
19
FTT
PPS-EOP
20
MCF
PPS-EOM
21
PIP, PIN
PPS-MPS, PPS-NULL
22
RTN, RTP
PRI-Q
23
No signal, DCN
DCN
24
PPR
25
RNR
RR
26
CTR
CTC
27
ERR
EOR-Q
28
PPS-PRI-Q
29
V.8 Phase-1
V.8 Phase-1
30
V.8 Phase-2
V.8 Phase-2
31
V.8 Phase-3
V.8 Phase-3
Result code
(Communication
result)
Communication
report result
column
Communication interruption
content
0 – 31
Refer to the pre-
vious table.
vious table.
Depends on the communication
disconnection position. For 16 or
later, V.34 mode communication.
disconnection position. For 16 or
later, V.34 mode communication.
33
Busy
The calling side cannot connect
the line with the other party.
the line with the other party.
34
Cancel
When a communication interrup-
tion command is delivered during
transmission or reception, <Send/
Receive/Poll/Bulletin>
When the operation is interrupted
by the stop key.
tion command is delivered during
transmission or reception, <Send/
Receive/Poll/Bulletin>
When the operation is interrupted
by the stop key.
35
Power OFF
When the power is cur off during
sending or receiving, <Send/
Receive/Poll/Bulletin>
sending or receiving, <Send/
Receive/Poll/Bulletin>
38
Reception mem-
ory over
ory over
When memor y is over dur ing
reception, <Receive/Poll>.
When printing cannot be per-
formed during reception due to
inhibition of proxy reception,
<Receive/Poll>
reception, <Receive/Poll>.
When printing cannot be per-
formed during reception due to
inhibition of proxy reception,
<Receive/Poll>
Result
code
Final reception signal
(Transmitting side)
Final reception signal
(Receiving side)
Click on the first or last page to see other MX-FX10 service manuals if exist.