MX-FNX5. Service Manual 01.05.08 - Sharp Copying Equipment Service Manual (repair manual). Page 42

Read Sharp MX-FNX5 Service Manual online

MX-FNX5  OVERALL MACHINE INFORMATION  6 – 5
S31
STPPRHP
Top Fence HP 
Sensor
Detects the top fence at its home 
position.
S32
POPHP
Positioning Roller 
HP Sensor
Detects the home position of the 
positioning roller.
S33
OSAEHP
Stack Plate HP 
Sensor (Center)
Detects the home position of the 
center stack plate.
S34
OSAEMHP
Stack Plate HP 
Sensor (Front)
Detects the home position of the front 
stack plate.
S35
OSAEUHP
Stack Plate HP 
Sensor (Rear)
Detects the home position of the rear 
stack plate.
S36
STPMVHP
Stapler HP 
Sensor (Front/
Rear)
Detects the home position of the staple 
unit for side-to-side movement.
S37
STPPS1HP
Stapler Rotation 
Sensor 1
Paired with Stapler Rotation Sensor 2. 
This sensor pair controls the 
positioning of the corner stapler for the 
horizontal, 45
° angle, and 75° angle 
stapling positions.
S38
STPPS2HP
Stapler Rotation 
Sensor 2
Paired with Stapler Rotation Sensor 1. 
This sensor pair controls the 
positioning of the corner stapler for the 
horizontal, 45
° angle, and 75° angle 
stapling positions.
S39
PNCH_FLL
Punch-out 
Hopper Full 
Sensor
Detects when the punch-out hopper is 
full and detects when the punch tray is 
set.
S40
PNCHHP1
Punch HP 
Sensor 1
Detects the cam home position for the 
2-hole punch. After punching a sheet 
of paper, the cam returns to home 
position and stops. Home position 
depends on whether 2 holes or 3 holes 
are being made, so there are two 
punch HP sensors. Punch HP sensor 
1 is used when 2-hole punching is 
selected, and punch HP sensor 2 is 
used when 3-hole punching is 
selected. When the cutout enters the 
slot of the punch HP in use (sensor 1 
or 2-hole punching) the motor stops.
S41
PNCHHP2
Punch HP 
Sensor 2
Detects the cam home position for 3-
hole punch. After punching a sheet of 
paper, the cam returns to home 
position and stops. Home position 
depends on whether 2 holes or 3 holes 
are being made, so there are two 
punch HP sensors. Punch HP sensor 
1 is used when 2-hole punching is 
selected, and punch HP sensor 2 is 
used when 3-hole punching is 
selected. When the cut-out enters the 
slot of the punch HP in use (sensor 1 
or 2-hole punching) the motor stops.
S42
SFTJOGHP
Shift Tray Jogger 
HP Sensor
Detects the actuator on the rear shift 
tray jogger fence and switches off the 
shift tray jogger motor, and signals the 
machine to turn on the shift tray jogger 
retraction motor to raise the fences at 
the end of a job.
S43
SFTJGTHP
Shift Tray Jogger 
Retraction HP 
Sensor
Detects the jogger fences of the shift 
tray jogger unit at their home positions.
Sensors
No.
Name
Description
Solenoids
No.
Name
Description
SHTR_S
Staple Trimming 
Chute Solenoid
Opens and closes the trap door that 
drops staple trimmings into the stapling 
trimmings hopper.
Switches
No.
Name
Description
SW
Front Door Safety 
Switch
Detects when the front door is open. 
The finisher does not operate until the 
front door has been closed.
SW
Emergency Stop 
Switch
Switches the current job off and on to 
allow time for the operator to remove 
paper from the shift tray.
SW
Shift Tray Upper 
Limit Switch
Cuts the power to the shift tray lift 
motor when the shift tray position is at 
its upper limit.
Page of 50
Display

Click on the first or last page to see other MX-FNX5 service manuals if exist.