Read Sharp MX-FNX3 / MX-FNX4 Service Manual online
MX-FNX4 SIMULATION 9 – 2
3-3
Purpose
Operation test/Check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1) Select a target of the operation check with the touch panel.
2) Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
1) Select a target of the operation check with the touch panel.
2) Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1) Select an item corresponding to the adjustment content with [
1) Select an item corresponding to the adjustment content with [
↑]
and [
↓] keys on the touch panel.
2) Enter the adjustment value with 10-key.
3) Press [OK] key. (The set value is saved.)
3) Press [OK] key. (The set value is saved.)
<MX-PNX2A/B/C/D Punch module>
FPE
FPE
Punch motor lock detection
FPUC
Punch unit connection detection
FPHPD
Punch HP detection
FPSHPD
Punch horizontal resist HP detection
FPFDD
Punch front door open detection
FPDD
Punch dust detection
FPUDSW
Punch upper cover open/close detection SW
<MX-FNX3>
FINRPS
FINRPS
Entry port reverse path solenoid
FJPM
Interface transport motor
FJFM
Interface transport fan motor
FFM
Entry port transport motor
FAM
Bundle paper exit motor
FFJM
Alignment motor front
FRJM
Alignment motor rear
FSM
Staple shift motor
FTLM1
Tray 1 lift motor
FTLM2
Tray 2 lift motor
FFSM
Staple motor
FSWM
Oscillation motor
FASM
Rear edge assist motor
FINRRS
Inlet port roller separation solenoid
FBRRS
Buffer roller separation solenoid
FFDRRS
Paper exit roller separation solenoid
FBES
Buffer rear edge holding solenoid
FSHC
Shutter open/close clutch
FAORC
Bundle exit lower roller clutch
FIN SENSOR CHECK
CLOSE
SIMULATION NO.03-02
TEST
1/1
FJPID
FJPOD
FJPDD
FED
FAED1
FAED2
FAED3
FFJHPD
FSTHPD
FSD
FSTD
FFANLK
FRJHPD
FBED1
FBED2
FCCD
FSLD1
FPDD1
FSLD2
FASHPD
FSWHPD
FSWOPD
FSTPD
FSHPD
FSJOGD
FSAD
FSSUC
FSHTD
FCD
FFDD
F24V
FPSW1
FPSW2
FPSW3
FAED21
FAED22
FAED23
MX-FNX4
FSIFM
FSIFM
Saddle entry port transport motor
FSFM
Saddle transport motor
FSFOM
Paper folding motor
FSGM
Guide motor
FSJM
Saddle alignment motor
FSFSTM
Stitch motor front
FSRSTM
Stitch motor rear
FSLGM
Paper holding motor
FSFS
Saddle flapper solenoid
FS1DFS
Paper deflection plate 1 solenoid
FS2DFS
Paper deflection plate 2 solenoid
FSFCS
Transport plate contact solenoid
FPPM
Paper positioning motor
MX-PNX2A/B/C/D Punch module
FPNM
FPNM
Punch motor
FPSM
Punch horizontal resist motor
<MX-FNX3>
Item Display
Item
Set
range
Default
value
A FRONT
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
B STAPLE
REAR
Staple binding
position adjustment
(one position at the
rear)
position adjustment
(one position at the
rear)
94 -106
100
C STAPLE
FRONT
Staple binding
position adjustment
(one position in front)
position adjustment
(one position in front)
94 -106
100
D PUNCH
CENTER
Punch center
adjustment
adjustment
30 - 70
50
E PUNCH
HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
SIMULATION NO.03-03
TEST
FIN LOAD CHECK
EXECUTE
1/1
CLOSE
FINRPS
FJPM
FJFM
FFM
FAM
FFJM
FRJM
FSM
FTLM1
FTLM2
FFSM
FSWM
FASM
FINRRS
FBRRS
FFDRRS
FBES
FSHC
FAORC
Click on the first or last page to see other MX-FNX3 / MX-FNX4 service manuals if exist.