Read Sharp MX-FNX10 Service Manual online
MX-FN10 ADJUSTMENTS 8 – 2
NOTE: "A: SADDLE POSITION (Saddle binding position adjust-
ment)" and "B: FOLDING POSITION (Saddle folding posi-
tion adjustment)"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting
tion adjustment)"
The saddle binding position adjustment and the saddle
folding position adjustment can be executed in the system
setting menu. However, the adjustments in the system set-
ting are based on the adjustment value of this simulation.
If, therefore, the adjustment value of this simulation is set
to an extreme level, the adjustment range in the system
setting may be narrowed. (Adjustment range in the system
setting
5.0mm)
If the adjustment range in the system setting is to narrow,
change the adjustment value of this simulation.
In general, when the saddle binding position and the sad-
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
change the adjustment value of this simulation.
In general, when the saddle binding position and the sad-
dle folding positions are adjusted to the center by this simu-
lation, the above trouble will not occur.
2. Punch unit (option)
A. Punch unit and punch PWB destination setting
1)
When the punch PWB is replaced, the destination must be set
accordingly.
accordingly.
2)
Use the DIP switch and the push switch on the punch PWB to
set the destination.
set the destination.
3)
The DIP switch setting and destinations are shown in the table
below.
below.
4)
Destination setting procedures
a)
a)
Check to confirm that the punch unit power is turned OFF.
b)
Set the DIP switches 1, 2, and 4 to ON, then push and
hold the push switch and supply the power.
hold the push switch and supply the power.
c)
Set the DIP switch for a desired destination.
d)
Push the push switch to fix the destination setting. (The
LED flashes.)
LED flashes.)
e)
Check to confirm that the LED turns ON (fixed state), and
turn OFF the power of the punch unit.
turn OFF the power of the punch unit.
f)
Set all the DIP switches to OFF, and terminate the opera-
tion.
tion.
5)
Checking the currently set destination
a)
a)
Check to confirm that the punch unit power is turned OFF.
b)
Set the DIP switches 1, 2, and 4 to ON, then push and
hold the push switch and supply the power.
hold the push switch and supply the power.
c)
Set the DIP switches 1 and 4 to OFF. (In this case, only
the DIP switch 2 is set to ON.)
the DIP switch 2 is set to ON.)
d)
Push the push switch, and check the number of flashing of
the LED.
(Since the first cycle includes the first lighting of the LED,
count the number of flashing in the second cycle.)
the LED.
(Since the first cycle includes the first lighting of the LED,
count the number of flashing in the second cycle.)
e)
Turn OFF the power of the punch unit.
f)
Set all the DIP switches to OFF, and terminate the opera-
tion.
tion.
J
STAPLE
PITCH
PITCH
Staple
binding
position
adjustment
(Two
positions
pitch)
binding
position
adjustment
(Two
positions
pitch)
0.2mm
Large value: The pitch of
two positions becomes
wider.
Small value: The pitch of
two positions becomes
narrower.
two positions becomes
wider.
Small value: The pitch of
two positions becomes
narrower.
K
PUNCH
CENTER
CENTER
Punch
center
adjustment
center
adjustment
0.2mm
Large value: The hole
position is shifted to the
front side from the center.
Small value: The hole
position is shifted to the
rear side from the center.
position is shifted to the
front side from the center.
Small value: The hole
position is shifted to the
rear side from the center.
L
PUNCH
HOLE
HOLE
Punch hole
position
adjustment
position
adjustment
0.2mm
Large value: The distance
between the hole position
and the paper edge
becomes shorter.
Small value: The distance
between the hole position
and the paper edge
becomes longer.
between the hole position
and the paper edge
becomes shorter.
Small value: The distance
between the hole position
and the paper edge
becomes longer.
M
SADDLE_
ADJUST_
POS
ADJUST_
POS
Saddle
alignment
position
adjustment
alignment
position
adjustment
0.2mm
Large value: The
alignment plate position is
shifted to the center.
Small value: The
alignment plate position is
shifted to the outside.
alignment plate position is
shifted to the center.
Small value: The
alignment plate position is
shifted to the outside.
N
GRIPPER_
POS
POS
Gripper exit
position
adjustment
position
adjustment
0.2mm
Large value: The gripper
exit position is shifted to
the front.
Small value: The gripper
exit position is shifted to
the rear.
exit position is shifted to
the front.
Small value: The gripper
exit position is shifted to
the rear.
Item
Display
Item
Change
Change direction
Model
Kind of punch
DIP switch
1
2
3
4
MX-PNX5 (2-hole)
2-hole type
OFF
OFF
OFF
OFF
MX-PNX5 (2/3-hole)
2/3-hole type
OFF
OFF
OFF
ON
MX-PNX5
(4-hole France)
(4-hole France)
4-hole type
(France)
(France)
OFF
OFF
ON
OFF
MX-PNX5
(4-hole Sweden)
(4-hole Sweden)
4-holel type
(Sweden)
(Sweden)
OFF
OFF
ON
ON
㪦㪥
㪈
㪉
㪊
㪋
㪚㪧㪬
㪣㪜㪛
㪧㫌㫅㪺㪿㩷㪧㪮㪙
㪛㪠㪧㩷㫊㫎㫀㫋㪺㪿
㪧㫌㫊㪿㩷㫊㫎㫀㫋㪺㪿
Click on the first or last page to see other MX-FNX10 service manuals if exist.