Read Sharp MX-FN27 Service Manual online
SERVICE MANUAL
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
[1] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
[2] EXTERNAL VIEW AND INTERNAL STRUCTURE . . . . . . . . . . . . . 2-1
[3] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[4] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[5] DISASSEMBLY AND ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[6] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
[7] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
TopPage
CONTENTS
CODE: 00ZMXFN27NS1E
MX-FN27 N
MX-PN14
MX-PN14
MODEL
DIGITAL MULTIFUNCTIONAL
SYSTEM OPTION
FINISHER
PUNCH UNIT
SYSTEM OPTION
FINISHER
PUNCH UNIT
CONTENTS
[1] SPECIFICATIONS
1. Finisher section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2. Stacker section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
3. Staple section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
4. Staple-free staple section . . . . . . . . . . . . . . . . . . . . . . . 1-2
5. Manual staple section . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
6. Punch Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
7. Ejectable Paper size/weight . . . . . . . . . . . . . . . . . . . . . 1-4
8. Loading number per size . . . . . . . . . . . . . . . . . . . . . . . 1-6
[2] EXTERNAL VIEW AND INTERNAL STRUCTURE
1. External view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2. Cross view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
3. Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
4. Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
5. Solenoid and switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
6. Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
7. PWB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
8. Punch unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
[3] ADJUSTMENTS
1. Punch Unit (MX-PN14) . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
[4] MAINTENANCE
1. Finisher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
2. Punch unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
[5] DISASSEMBLY AND ASSEMBLY
1. Major unit and cover . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
2. Motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
3. PWBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
4. Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
5. Other Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
[6] OPERATIONAL DESCRIPTION
1. Basic Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
2. Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
3. Feed Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
4. Processing Tray Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
5. Stack Tray Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
6. Jam Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17
7. Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18
[7] ELECTRICAL SECTION
1. Actual wiring chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
NOTE FOR SERVICING
1. Precautions for servicing
At servicing, be sure to turn off the power source according to the
specified steps and disconnect the power plug.
specified steps and disconnect the power plug.
Do not turn off the power switch when downloading is under way.
Turning off the main power switch while downloading is under way
can disable the machine.
can disable the machine.
When performing cleaning using organic solvent such as alcohol,
be sure to check that the component of solvent is vaporized com-
pletely before assembling.
be sure to check that the component of solvent is vaporized com-
pletely before assembling.
– Disconnect the power plug to avoid any potential dangers during
assembling/disassembling works.
– If not specially instructed, reverse the order of disassembly to
reinstall.
– Ensure to use the right screw type (length, diameter, etc.) at the
right position when assembling.
– To keep electric conduction, binding screws with washers are
used to attach the grounding wire and the varistor. Ensure to use
the right screw type when assembling.
the right screw type when assembling.
– Unless it is specially needed, do not operate the device with
some parts removed.
– Never remove the paint-locked screws when disassembling.
2. Screw tightening torque
For reduction in weight, thin plates are used in some parts of this
machine.
machine.
In the case of a screw hole with a triangle mark near it as shown in
the figure below, strongly tightening the screw may damage or
deform the screw hole.
the figure below, strongly tightening the screw may damage or
deform the screw hole.
In the case of a screw hole with a triangle mark, take care not to
apply too much force when tightening the screw.
apply too much force when tightening the screw.
The recommended torque value is shown below as a reference value.
3. Identification method for N model series
Type of Screws
RS tight
W Sems
Binding
TP
Fastened member
Metal
Resin
Metal
Resin
Metal
Resin
Metal
Resin
Tightening torque
(N*m)
(N*m)
M4
Approx. 1.6
Approx. 1.6
Approx. 1.6
Approx. 0.8
Approx. 1.6
Approx. 0.8
Approx. 1.6
Approx. 0.8
M3
Approx. 0.8
Approx. 0.8
Approx. 0.6
Approx. 0.6
Approx. 0.6
Approx. 0.6
Approx. 0.6
Approx. 0.6
Type of Screws
RS tight
W Sems
Binding
TP
Symbols in this manual
The lists of symbols used in this manual are shown below.
The meaning of each symbol described in the table must be understood for proper servicing
The following rules apply throughout this Service Manual:
1. Each chapter contains sections explaining the purpose of specific
functions and the relationship between electrical and mechanical
systems with reference to the timing of operation.
systems with reference to the timing of operation.
In the diagrams, represents the path of mechanical drive; where
a signal name accompanies the symbol, the arrow indicates the
direction of the electric signal.
direction of the electric signal.
The expression "turn on the power" means flipping on the power
switch, closing the front door, and closing the delivery unit door,
which results in supplying the machine with power.
which results in supplying the machine with power.
2. In the digital circuits, '1' is used to indicate that the voltage level
of a given signal is "High", while '0' is used to indicate "Low".
(The voltage value, however, differs from circuit to circuit.) In
addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
(The voltage value, however, differs from circuit to circuit.) In
addition, the asterisk (*) as in "DRMD*" indicates that the DRMD
signal goes on when '0'.
In practically all cases, the internal mechanisms of a micropro-
cessor cannot be checked in the field. Therefore, the operations
of the microprocessors used in the machines are not discussed:
they are explained in terms of from sensors to the input of the
DC controller PCB and from the output of the DC controller PCB
to the loads.
of the microprocessors used in the machines are not discussed:
they are explained in terms of from sensors to the input of the
DC controller PCB and from the output of the DC controller PCB
to the loads.
The descriptions in this Service Manual are subject to change
without notice for product improvement or other purposes, and
major changes will be communicated in the form of Service Infor-
mation bulletins.
without notice for product improvement or other purposes, and
major changes will be communicated in the form of Service Infor-
mation bulletins.
All service persons are expected to have a good understanding of
the contents of this Service Manual and all relevant Service Infor-
mation bulletins and be able to identify and isolate faults in the
machine.
the contents of this Service Manual and all relevant Service Infor-
mation bulletins and be able to identify and isolate faults in the
machine.
Symbols
Explanation
Symbols
Explanation
Check.
Remove the claw.
Check visually.
Insert the claw.
Check a sound.
Push the part.
Disconnect the connector.
Connect the power cable.
Connect the connector.
Disconnect the power cable.
Remove the cable/wire from the cable
guide or wire saddle.
guide or wire saddle.
Turn on the power.
Install the cable/wire to the cable guide or
wire saddle.
wire saddle.
Turn off the power.
Remove the screw.
Loosen the screw.
Install the screw.
Tighten the screw.
Cleaning is needed.
Measurement is needed.
1x
1x
1x
1x
1x
1x
1x
1x
