Read Sharp MX-FN19 / MX-FN20 / MX-PN12 (serv.man4) Service Manual online
MX-7040N MX-FN20 (SADDLE STITCH FINISHER (50 sheets binding)) 14 – 1
MX-7040N
Service Manual
[14] MX-FN20 (SADDLE STITCH FINISHER (50 sheets binding))
Since the illustrations of the former models are used, they may differ from the actual cases.
1. Unpacking
A. Removal of the saddle stitch finisher
NOTE: For removal of the saddle stitch finisher, manpower of two
persons or more is required.
1)
Remove the fixing material, and remove the top case.
2)
Remove the bundled items from packing cushion.
3)
Holding the upper part of the saddle stitch finisher by two peo-
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot. )
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot. )
4)
Remove the skid and packing cushions.
5)
One person tilt the saddle stitch finisher, another person
remove the lower tray.
remove the lower tray.
6)
Remove the other side similarly.
MX-7040N MX-FN20 (SADDLE STITCH FINISHER (50 sheets binding)) 14 – 2
B. Removal of the protection material
1)
Remove the fixing tapes and protection material.
2)
Remove the screws and remove the fixing material for paper
exit tray. (four positions)
exit tray. (four positions)
3)
Open the front door of the finisher, and remove the fixing tapes
and protection material.
and protection material.
4)
Pull out the stapler unit.
MX-7040N MX-FN20 (SADDLE STITCH FINISHER (50 sheets binding)) 14 – 3
5)
Remove the screw, and remove the fixing material of the sta-
pler unit.
pler unit.
6)
Replace the stapler unit to the original position, and close the
front door.
front door.
7)
Remove the fixing screws, and remove the right lower cover.
8)
Remove the fixing screws, and remove the pressure release
plates of saddle section.
plates of saddle section.
9)
Attach the right lower cover with the fixing screws.
C. Packed items check
No.
Name
Quantity
1
Binding head round tapping M4 x 8
2
2
IT tapping M4 x 20
2
3
Binding head M4 x 12
4
4
Step screw
2
5
Rail
1
6
Rail reception sheet metal
1
7
Connection fixture F (for x4)
1
8
Connection fixture R (for x4)
1
9
Staple position label (For scanner)
1
10
Staple position label (For DSPF)
1
11
Punch position label (For scanner)
1
12
Punch position label (For DSPF)
1
13
Cushion (S)
1
14
Cushion (M)
1
15
Cushion (L)
1
1
2
3
6
4
5
7
8
9
11
12
10
X4
13
15
14
MX-7040N MX-FN20 (SADDLE STITCH FINISHER (50 sheets binding)) 14 – 4
2. Installation
NOTE: When the saddle finisher is installed, first install the paper
pass unit, and then install the saddle finisher.
NOTE: When the saddle finisher and punch unit is installed at the
same time, first install the punch unit, and then install the
saddle finisher.
saddle finisher.
A. Installation of the rail
1)
Install the rail (Packed items (No.5)) to the saddle stitch fin-
isher with the fixing screws (Packed items (No.1)).
isher with the fixing screws (Packed items (No.1)).
2)
Install the rail reception sheet metal (Packed items (No.6)) to
the main unit with the fixing screws (Packed items (No.2)).
the main unit with the fixing screws (Packed items (No.2)).
B. Installation of the connection fixture F/R
1)
Install the connection fixture R (Packed items (No.8)) to the
main unit with the fixing screws (Packed items (No.3)).
main unit with the fixing screws (Packed items (No.3)).
2)
Install the connection fixture F (Packed items (No.7)) to the
main unit with the fixing screws (Packed items (No.3)).
main unit with the fixing screws (Packed items (No.3)).
C. Attaching the cushion
1)
Attach the cushion (S) (Packed items), the cushion (M)
(Packed items) and the cushion (L) (Packed items) to the posi-
tion indicated in the figure.
(Packed items) and the cushion (L) (Packed items) to the posi-
tion indicated in the figure.
Cushion A
attachment
position
attachment
position
Cushion B
attachment
position
attachment
position
Cushion C
attachment
position
attachment
position
Cushion A attachment
reference (Front edge of
the relay path left
cabinet)
reference (Front edge of
the relay path left
cabinet)
Cushion A attachment
reference (Upper side of
the groove in the relay
path left cabinet)
reference (Upper side of
the groove in the relay
path left cabinet)
Cushion B attachment
reference (Upper edge
of the machine left
cabinet)
reference (Upper edge
of the machine left
cabinet)
Cushion B attachment
reference (Rear edge of
the handle hole)
reference (Rear edge of
the handle hole)
Cushion C attachment
reference (Front edge of
the upper cushion)
reference (Front edge of
the upper cushion)
Cushion C attachment
reference (Upper edge of the
machine left lower cabinet)
reference (Upper edge of the
machine left lower cabinet)
