Read Sharp MX-FN17 / MX-PN11 Service Manual online
MX-FN17 ADJUSTMENTS AND SETTINGS 3 – 1
MX-FN17
Service Manual
[3] ADJUSTMENTS AND SETTINGS
Each adjustment item in the adjustment item list is identified with its
own JOB No. The adjustments are basically executed in the
sequence from a smaller JOB No. to a larger JOB No.
There is, however, no need to perform all the adjustment items.
Only the necessary items may be executed depending on the situa-
tion.
Unnecessary items may be skipped to go to the next necessary
item. In this case, of course, the adjustment sequence could be
executed from a smaller to a larger JOB No.
If the above is neglected, the adjustment cannot be completed nor-
mally, resulting in a trouble.
Start of simulation
1)
own JOB No. The adjustments are basically executed in the
sequence from a smaller JOB No. to a larger JOB No.
There is, however, no need to perform all the adjustment items.
Only the necessary items may be executed depending on the situa-
tion.
Unnecessary items may be skipped to go to the next necessary
item. In this case, of course, the adjustment sequence could be
executed from a smaller to a larger JOB No.
If the above is neglected, the adjustment cannot be completed nor-
mally, resulting in a trouble.
Start of simulation
1)
Press [COPY MODE] key to enter the copy mode.
2)
Press [P] (Program) key
→ [*] (Asterisk) key → [C] (Clear) key
→ [*] (Asterisk) key in this sequence.
3)
The display is shifted to the simulation main number entry
screen (entry standby screen).
screen (entry standby screen).
1. Adjustments and settings item list
2. Details
ADJ 1
Punch unit, punch PWB
destination setting
destination setting
1)
When the punch PWB is replaced, the destination setting must
be performed.
be performed.
2)
For destination setting, the DIP switch (SW1) on the punch
PWB is used.
PWB is used.
3)
The relationship between the switches and the destinations is
shown in the table below.
shown in the table below.
ADJ 2
Flapper solenoid adjustment
When the flapper solenoid is disassembled, an adjustment is
required when assembling.
1)
required when assembling.
1)
Loosen the solenoid fixing screw.
2)
Slide the solenoid in the direction of arrow A.
3)
Hold the solenoid, and pull out the plunger in the direction of
arrow B.
arrow B.
4)
Gradually slide the solenoid in the direction arrow C without
touching the plunger, and fix it to the position where the gap
between lever X and Y is 0 - 0.5mm.
touching the plunger, and fix it to the position where the gap
between lever X and Y is 0 - 0.5mm.
5)
Manually turn ON the solenoid, and check to confirm that the
gate tip is over the lower surface of the paper guide.
gate tip is over the lower surface of the paper guide.
JOB No.
Adjustment and setting item
Simulation
to be used
to be used
ADJ 1
Punch unit, punch PWB destination setting
–
ADJ 2
Flapper solenoid adjustment
–
Model
Kind of punching
1
2
MX-PN11A
2-hole type
OFF
OFF
MX-PN11B
2/3-hole type
ON
OFF
MX-PN11C
4-hole type (France)
OFF
ON
MX-PN11D
4-hole type (Sweden)
ON
ON
㪦㪥
㪈
㪉
A
B
C
Plunger
Solenoid
0 - 0.5mm
Lever X
Lever Y
Gate tip
Lower surface of the
paper guide
paper guide
Click on the first or last page to see other MX-FN17 / MX-PN11 service manuals if exist.