Read Sharp MX-EB13 Service Manual online
SERVICE MANUAL
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
SHARP CORPORATION
[1] UNPACKING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[2] INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[3] SYSTEM SETTING CHANGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
[4] SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TopPage
CONTENTS
CODE: 00ZMXEB13/S1E
MX-EB13
MODEL
USB WIRELESS ADAPTER
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
COPYRIGHT
©
XXXX BYSHARP CORPORATION
ALL RIGHTS RESERVED.
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
LEAD-FREE SOLDER
The alphabet following the LF mark shows the kind of lead-free solder.
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting-point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the
exclusive-use soldering iron is recommended.
exclusive-use soldering iron is recommended.
(2) NOTE FOR SOLDERING WORK
Since the melting-point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering
capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when
completion of soldering is confirmed.
capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when
completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron
tip after completion of soldering work.
tip after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
Example:
5mm
Lead-Free
Solder composition
code (Refer to the
table at the right.)
code (Refer to the
table at the right.)
<Solder composition code of lead-free solder>
Solder composition
Sn-Ag-Cu
Sn-Ag-Bi
Sn-Ag-Bi-Cu
Sn-Ag-Bi-Cu
Sn-Zn-Bi
Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
Bi-Sn-Ag-P
Bi-Sn-Ag
Bi-Sn-Ag
a
b
z
i
n
s
p
Solder composition code
a
CONTENTS
[1]
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
A. Confirmation of items packed (MX-EB13). . . . . . . . . . . . 1
[2]
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
[3]
SYSTEM SETTING CHANGE . . . . . . . . . . . . . . . . . . . . . . . 1
A.Simulation setting change. . . . . . . . . . . . . . . . . . . . . . . . . 1
B. Setting change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
C. Confirmation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
D. Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
[4]
SPECIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
A. LED Specifiaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
B. Basic Specifiaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Corresponding Protocol . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. Connectable Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1
1. Unpacking
A. Confirmation of items packed (MX-EB13)
No. Parts
name Qty
1
USB wireless LAN adopter
1
2 Operation
manual
1
3 Warning
sticker
1
2. Installation
Before installation, turn the operation panel and
main power switches on the main machine OFF and unplug the
power cord.
1) Connect the USB wireless LAN adopter to the USB
terminal on the main machine.
Always connect it to the USB terminal on the side or the rear
side of the main unit. Never connect it to the terminal at the
front of the operation panel.
2) Reboot the machine.
After connected from the wired LAN to wireless LAN and vice
versa, always reboot the main machine.
3. System Setting Change
A. Simulation setting change
1. Enter SIM26-50.
2. Change the “WIRELESS SET” setting value from “0(NO)” to
“1(YES)”.
B. Setting change
1) Connection type change
1.Go into the following setting menu mode.
Home→Settings→Administrator Login→
Network Settings→Wireless Settings
2. Set the Network settings to the Wireless.
Name of
setting
Setting Available
I/F
Connection
Type
Switching
Type
Switching
Wired Only(default)
Wireless LAN: Disable
Wired LAN: Enable
Wired LAN: Enable
Wireless
(Infrastructure Mode)
(Infrastructure Mode)
Wireless LAN:
Enable (operable as
a cordless handset)
Wired LAN: Disable
Enable (operable as
a cordless handset)
Wired LAN: Disable
Wired + Wireless
(Ad-hoc Mode)
(Ad-hoc Mode)
Wireless LAN:
Enable (operable as
a cordless handset)
Wired LAN: Enable
Enable (operable as
a cordless handset)
Wired LAN: Enable
3. Press [Submit] key.
4. Press [Reboot Now] key. The following message appears.
Now turning off the power.
2) Access point registration
Go into the following setting menu mode.
Home→Settings→Administrator Login→
Network Settings→Wireless Settings
1. Press [Setup] key.
1