Read Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man61) Technical Bulletin online
5
5.
12
12.
3
3.
Slide the rear lower PG with the caution
label of High-temperature affixed in the
direction of arrow.
Slide the rear lower PG with the caution
label of High-temperature affixed in the
direction of arrow.
10
10.
Remove the pressure SP from the
fusing release lever from both F/R, and
pull it out from the area indicated with
red circle of the left picture.
Remove the pressure SP from the
fusing release lever from both F/R, and
pull it out from the area indicated with
red circle of the left picture.
(For both
F/R)
For detail, see the picture of No.11.
For detail, see the picture of No.11.
4
4.
Pull the rear lower PG toward you while
sliding it at Step 3 like the left picture so
that the rear lower PG can be removed.
Pull the rear lower PG toward you while
sliding it at Step 3 like the left picture so
that the rear lower PG can be removed.
*The spring is attached at R side. Keep
it to avoid the loss.
*Conduct the work while the rear lower
PG is removed. Otherwise, the
pressure roller may be damaged.
it to avoid the loss.
*Conduct the work while the rear lower
PG is removed. Otherwise, the
pressure roller may be damaged.
11
11.
Like shown in the left picture, the
pressure SP is hooked at Step10 but the
fusing release lever can be removed by
dismounting the pressure SP from the
fusing frame.
Like shown in the left picture, the
pressure SP is hooked at Step10 but the
fusing release lever can be removed by
dismounting the pressure SP from the
fusing frame.
●
Fusing release lever - Replacing Manual (Disassembling)
1
1.
Place the fusing unit while the caution
label of High-temperature is facing
toward you.
The picture of No.2 is the enlarged view
of the area indicated with red circle.
Place the fusing unit while the caution
label of High-temperature is facing
toward you.
The picture of No.2 is the enlarged view
of the area indicated with red circle.
8
8.
Reverse the fusing unit 180-degree
from Step 7. The picture of No.9 is the
enlaged view of the area indicated with
red circle.
Reverse the fusing unit 180-degree
from Step 7. The picture of No.9 is the
enlaged view of the area indicated with
red circle.
2
2.
Remove the screw in the area indicated
with red circle of the left picture.
Remove the screw in the area indicated
with red circle of the left picture.
9
9.
Remove the pressure SP hooked to the
fusing frame in the area indicated with
red circle.
Remove the pressure SP hooked to the
fusing frame in the area indicated with
red circle.
(For both F/R)
7
7.
After removing the support SP at Step 6,
place the unit in the same direction as
Step1.
After removing the support SP at Step 6,
place the unit in the same direction as
Step1.
This is the end of
disassembling.
Place the fusing unit while the support
SP mounted to the lateral side is facing
toward you. (For both F/R).
SP mounted to the lateral side is facing
toward you. (For both F/R).
After removing the fusing release levers
(both F/R), the pressure roller lever
opens like the left picture.
(both F/R), the pressure roller lever
opens like the left picture.
6
6.
Remove the support SP
Remove the support SP
(For both F/R)
.
13
13.
Lift up the fusing release lever in the
area indicated with red circle of the left
picture and then remove it (For both
F/R).
Lift up the fusing release lever in the
area indicated with red circle of the left
picture and then remove it (For both
F/R).
Click on the first or last page to see other MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man61) service manuals if exist.