Read Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man12) User Guide / Operation Manual online
4
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be
easily accessible.
Shielded interface cables must be used with this equipment to
maintain compliance with EMC regulations.
The equipment should be installed near an accessible socket outlet
for easy disconnection.
Each instruction also covers the optional units used with these products.
For the users of the fax function
(for MX-C250F/C300F/C300W)
FAX interface cable and Line cable:
These special accessories must be used with the device.
The declaration of conformity may be consulted at:
http://www.sharp.de/doc/MX-C300W_MX-C300WE.pdf
http://www.sharp.de/doc/MX-C250F_MX-C250FE.pdf
Important safety instructions
• If any of your telephone equipment is not operating properly, you
should immediately remove it from your telephone line, as it may
cause harm to the telephone network.
• Never install telephone wiring during a lightning storm.
• Never install telephone socket in wet locations unless the socket is
specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
• Do not use a telephone to report a gas leak in the vicinity of the
leak.
• Do not install or use the machine near water, or when you are wet.
Take care not to spill any liquids on the machine.
• Save these instructions.
Important Notice for New Zealand Users
General
"The grant of a Telepermit for any item of terminal equipment
indicates only that Telecom has accepted that the item complies
with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort
of warranty. Above all, it provides no assurance that any item will work
correctly in all respects with another item of Telepermitted equipment
of a different make or model, nor does it imply that any product is
compatible with all of Telecom’s network services."
This equipment is not capable, under all operating conditions, of
This equipment is not capable, under all operating conditions, of
correct operation at the higher speeds for which it is designed.
Telecom will accept no responsibility should difficulties arise in these
circumstances. This condition typically applies to 56 kbit/s modems.
This equipment shall not be set up to make automatic calls to
This equipment shall not be set up to make automatic calls to
Telecom’s 111 Emergency Service.
This equipment should not be used under any circumstances that
This equipment should not be used under any circumstances that
may constitute a nuisance to other Telecom customers.
This equipment may not provide for the effective hand-over of a call
This equipment may not provide for the effective hand-over of a call
to another device connected to the same line.
In order to operate within the limits for compliance with Telecom’s
In order to operate within the limits for compliance with Telecom’s
specifications, the associated equipment shall be set to ensure that automatic
calls to different numbers are spaced such that there is not less than 5
seconds between the end of one call attempt and the beginning of another.
Notice for Users in Australia and New Zealand
Your fax machine and the telephone system
WARNING NOTICE:
NO calls can be made to or from this fax during a mains power failure.
WARNING
WARNING
Australian Communications and Media Authority (ACMA) regulations
state that no unauthorised changes or modifications to this equipment
are permitted.
Complies with the following standards,
AS/NZS 60950.1
AS/ACIF S002, NZ TELECOM and AS/NZS CISPR 22
These limits are designed to provide reasonable protection against
interference in an installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause interference. However, there
is no guarantee that interference will not occur in a particular installation.
SOFTWARE LICENCE
The SOFTWARE LICENCE will appear when you install the software
from the CD-ROM. By using all or any portion of the software on the
CD-ROM or in the machine, you are agreeing to be bound by the
terms of the SOFTWARE LICENCE.
• The explanations in this manual assume that you have a working
knowledge of your Windows or Macintosh computer.
• For information on your operating system, please refer to your
operating system manual or the online Help function.
• The explanations of screens and procedures in this manual are
primarily for Windows 7 in Windows
®
environments. The screens
may vary depending on the version of the operating system.
• This manual contains references to the fax function. However, please
note that the fax function is not available in some countries and regions.
• This manual contains explanations of the PC-Fax driver and PPD
driver. However, please note that the PC-Fax driver and PPD driver
are not available and do not appear on the software for installation in
some countries and regions.
In this case, please install the English version if you want to use
these drivers.
• Considerable care has been taken in preparing this manual. If
you have any comments or concerns about the manual, please
contact your dealer or nearest authorised service representative.
• This product has undergone strict quality control and inspection
procedures. In the unlikely event that a defect or other problem
is discovered, please contact your dealer or nearest authorised
service representative.
• Aside from instances provided for by law, SHARP is not responsible for
failures occurring during the use of the product or its options, or failures
due to incorrect operation of the product and its options, or other
failures, or for any damage that occurs due to use of the product.
Products that have earned the ENERGY STAR
®
are designed to protect the environment
through superior energy efficiency.
through superior energy efficiency.
The products that meet the ENERGY STAR
®
guidelines carry the
ENERGY STAR
®
logo.
The products without the logo may not meet the ENERGY STAR
®
guidelines.
This product is designed for commercial application only and
as such it falls outside the scope of Regulation (EC) 1275/2008
implementing EU Directive 2005/32/EC on eco-design requirements
for standby and off mode electric power consumption. Sharp does
not recommend the product for domestic application and will not
accept any liability for such use.
as such it falls outside the scope of Regulation (EC) 1275/2008
implementing EU Directive 2005/32/EC on eco-design requirements
for standby and off mode electric power consumption. Sharp does
not recommend the product for domestic application and will not
accept any liability for such use.
Warranty
While every effort has been made to make this document as accurate
and helpful as possible, SHARP Corporation makes no warranty of
any kind with regard to its content. All information included herein is
subject to change without notice. SHARP is not responsible for any
loss or damages, direct or indirect, arising from or related to the use
of this operation manual.
© Copyright SHARP Corporation 2013. All rights reserved.
Reproduction, adaptation or translation without prior written
permission is prohibited, except as allowed under copyright laws.
If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a different circuit to that
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The Ringer Equivalence Number (REN) for this equipment is written
on the label.
Important safety information
In Australia, installing or modifying telephone lines should only be
done by an ACMA licenced serviceman. In New Zealand, installing
or modifying telephone lines should be done in accordance with
Telecom wiring practices.
Wireless LAN (for MX-C300W)
The communication range of wireless LAN may shorten or
communication may not be possible in some usage environments,
due to shielding materials, the installation location, the effects of
ambient radio noise, data transmission speed, and other factors.
Click on the first or last page to see other MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man12) service manuals if exist.