Read Sharp MX-6240N / MX-7040N (serv.man91) Technical Bulletin online
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-1471
[Description]
No.
Item
Details
1
Main unit control
Modification of L8-20 which may occur when condition signalling between internal modules is
not done properly.
not done properly.
2
Main unit control
Modification of a failure to complete Fax firmware upgrade during firmware upgrade
3
Main unit control
Modification of a failure to restart the unit properly while acquiring the image (snapshot) during
the firmware upgrade due to lack of some data necessary.
the firmware upgrade due to lack of some data necessary.
4
Main unit control
Modification of the problem that the colour changes before and after the halftone process
control if the correction amount of halftone process control largely changes from the previous
value.
control if the correction amount of halftone process control largely changes from the previous
value.
5
Main unit control
Modification of Scan job which keep remaining internally. The problem occurs if Eco scan
setting was enabled but cancelled after previewing for Copy job.
setting was enabled but cancelled after previewing for Copy job.
6
Main unit control
Modification of the problems that FAX receiving may stop after reaching to the pre-set limit or
the job may disappear when printing because the internal processing at the time of job
completion cannot work correctly.
the job may disappear when printing because the internal processing at the time of job
completion cannot work correctly.
7
Main unit control
Correction of the problem that the trimmer function of Copy mode becomes unavailable when
using the account application.
using the account application.
8
Main unit control
Correction of slower performance during batch printing while MFP is in vendor mode.
9
Main unit control
Modification of a problem which occurs with following steps: 1) Print out a test pattern in Paper
Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers to the
bypass tray. 4) The test pattern is printed in simplex.
Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers to the
bypass tray. 4) The test pattern is printed in simplex.
10 UI
Modification of a failure to delete the job completed from Job Status (Direct print from USB flash
drive). User cannot delete the job on the Job Status screen.
drive). User cannot delete the job on the Job Status screen.
11 UI
Modification of a problem with "Automatically print stored jobs after login" in User Control which
is disabled while external authentication for OSA is enabled.
is disabled while external authentication for OSA is enabled.
12 Network
Factory default of LPD timeout period is changed from 0 (infinite) to 90 sec.
*The value above will not be changed when updating the firmware in the field.
*The value above will not be changed when updating the firmware in the field.
13 Network
Modification of machine lockup (ex. operation panel does not function) due to the unauthorized
memory access caused by defective internal management processing in WSD module.
memory access caused by defective internal management processing in WSD module.
14 Network
The modification of garbled images which appear while the data communication speed of a
device is 10 Mbps.
device is 10 Mbps.
15 Network
Modification of a communication error which occurs in case the devices with different MAC
address share same IP address (i.e. load balancer is installed).
address share same IP address (i.e. load balancer is installed).
16 Network
Modification of different Fax event notification between OSA4.5 and OSA4.1
17 Network
Correction of the problem that the machine locks up when accessing the specific MIB with the
undefined INDEX.
undefined INDEX.
18 Network
Modification of an error to authenticate IEEE802.1X for wired LAN
19 Network
Modification of network lockup which occurs during the port scan on tandem port.
20 Network
Enabling display of Machine ID information in MIB
21 Network
Modification is made so that prompt authentication by a login user is enabled/disabled in Soft
SW.
SIM55-3 SW No.24 Data3
0: Enabled (Default for all destinations other than Europe)
1: Disabled
SW.
SIM55-3 SW No.24 Data3
0: Enabled (Default for all destinations other than Europe)
1: Disabled
22 Printer
Modification of print operation which may stop displaying "Rendering" during mass printing.
23 Printer
Correction of the problem that the machine may lock up when printing the data including the
specific font with PCL6.
specific font with PCL6.
24 Printer
Correction of the problem that the performance may be slowing down in the process of
continuous printing.
continuous printing.
25 Printer
Setup of the print port for Web Page
26 Printer
Correction of the problem that the performance becomes worse or the print job is completed
without printing all data when printing with PS in some cases.
without printing all data when printing with PS in some cases.
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man91) service manuals if exist.