Read Sharp MX-6240N / MX-7040N (serv.man24) Service Manual online
MX-7040N ADJUSTMENTS AND SETTINGS 5 – 93
ADJ 19
Finisher and punch unit
adjustments (alignment, punch
hole position, staple position)
adjustments (alignment, punch
hole position, staple position)
This adjustment must be performed in the following cases:
* When the finisher is disassembled.
* When the finisher control PWB is replaced.
* When the punch unit is disassembled.
* When the punch control PWB is replaced.
* When the alignment is improper.
* When the punch hole position is shifted.
* When the staple position is shifted.
1)
Enter the SIM 3-10 mode.
2)
Select an adjustment target item with the scroll key.
4K finisher (50 sheet staple) (MX-FN19)
ǂǂǂ6,08/$7,21ǂǂ12
7(67
&/26(
˖)5217$'-867
˖67$3/(5($5
˖67$3/()5217
˖381&+&(17(5
˖381&++2/(
),1,6+(5$'-8670(17
$
˷̚˹
$˖
%˖
&˖
'˖
(˖
2.
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
%$&.
0212
&2/25
(;,7
&/($5
Item/Display
Content
Setting
range
Default
value
Purpose
(Case where the
adjustment is
required)
Change when the adjustment value is increased
or decreased
Change when
the adjustment
value is
changed by 1
A
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
When the paper
alignment capability
in the stacker
section is improper,
the paper alignment
width is adjusted.
alignment capability
in the stacker
section is improper,
the paper alignment
width is adjusted.
F side paper
alignment plate stop
position
(F/R direction)
alignment plate stop
position
(F/R direction)
When the adjustment value is
increased, the alignment
position is shifted to the
center.
When the adjustment value is
decreased, the alignment
position is shifted to the
outside.
increased, the alignment
position is shifted to the
center.
When the adjustment value is
decreased, the alignment
position is shifted to the
outside.
0.2mm
B
STAPLE REAR
Stapling position
adjustment (Rear,
one position)
adjustment (Rear,
one position)
94 -
106
106
100
When the stapling
position on the R
side is shifted, the
adjustment is
executed.
position on the R
side is shifted, the
adjustment is
executed.
Stapling position
(stapler stop
position)
(F/R direction)
(stapler stop
position)
(F/R direction)
When the adjustment value is
increased, the distance
between the stapling position
and the paper edge becomes
longer.
When the adjustment value is
decreased, the distance
between the stapling position
and the paper edge becomes
shorter.
increased, the distance
between the stapling position
and the paper edge becomes
longer.
When the adjustment value is
decreased, the distance
between the stapling position
and the paper edge becomes
shorter.
0.2mm
C
STAPLE
FRONT
FRONT
Stapling position
adjustment (one
position in front)
adjustment (one
position in front)
94 -
106
106
100
When the stapling
position on the F
side is shifted, the
adjustment is
executed.
position on the F
side is shifted, the
adjustment is
executed.
Stapling position
(stapler stop
position)
(F/R direction)
(stapler stop
position)
(F/R direction)
When the adjustment value is
decreased, the distance
between the stapling position
and the paper edge becomes
shorter.
When the adjustment value is
increased, the distance
between the stapling position
and the paper edge becomes
longer.
decreased, the distance
between the stapling position
and the paper edge becomes
shorter.
When the adjustment value is
increased, the distance
between the stapling position
and the paper edge becomes
longer.
0.2mm
D
PUNCH
CENTER
CENTER
Punch center
adjustment
adjustment
30 - 70
50
When the punch off-
center is shifted, the
adjustment is
executed.
center is shifted, the
adjustment is
executed.
Punching position
(F/R direction)
(F/R direction)
When the adjustment value is
increased, the hole position is
shifted to the front.
When the adjustment value is
decreased, the hole position
is shifted to the rear.
increased, the hole position is
shifted to the front.
When the adjustment value is
decreased, the hole position
is shifted to the rear.
0.2mm
E
PUNCH HOLE
Punch hole
position
adjustment
position
adjustment
46 - 52
50
When the punch
hole position is
shifted in the
transport direction,
the adjustment is
executed.
hole position is
shifted in the
transport direction,
the adjustment is
executed.
Punch position
(paper transport
direction)
(paper transport
direction)
When the adjustment value is
increased, the punch hole
position is shifted to the rear
edge of paper.
When the adjustment value is
decreased, the punch hole
position is shifted to the lead
edge of paper.
increased, the punch hole
position is shifted to the rear
edge of paper.
When the adjustment value is
decreased, the punch hole
position is shifted to the lead
edge of paper.
0.2mm
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man24) service manuals if exist.