Read Sharp MX-6240N / MX-7040N (serv.man24) Service Manual online
MX-7040N ADJUSTMENTS AND SETTINGS 5 – 7
2-B
Adjust the developing bias voltage
This adjustment must be performed in the following cases:
* When the MC high voltage power PWB is replaced.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
1)
Enter the SIM 8-1 mode.
2)
Select an output mode to be adjusted with the mode key and the scroll key.
3)
Enter the adjustment value (specified value) of the middle speed mode and press [OK] key.
Remark:
Normally when the default value is set, the specified voltage is out-
putted.
Normally when the default value is set, the specified voltage is out-
putted.
The adjustment value of each color mode is specified on the label
attached to the MC high voltage power PWB. Enter that value.
attached to the MC high voltage power PWB. Enter that value.
DVK:XXX DVC:XXX DVM:XXX DVY:XXX
When [EXECUTE] key is pressed, the voltage entered in the proce-
dure 3) is outputted for 30 sec and the set value is saved.
dure 3) is outputted for 30 sec and the set value is saved.
When [EXECUTE] key is pressed again, the output is stopped.
CAUTION: Note that the adjustment value may differ depending on
the MC high voltage power PWB.
Since the adjustment value label is attached on the MC
high voltage PWB, the PWB must be removed in order
to check the adjustment value.
high voltage PWB, the PWB must be removed in order
to check the adjustment value.
This is a troublesome procedure. Therefore, it is advis-
able to put down the adjustment value in advance.
able to put down the adjustment value in advance.
When the adjustment value (specified value) of the mid-
dle speed mode is set, the adjustment values of the
other modes are automatically set according to the mid-
dle speed mode setting in a certain relationship.
dle speed mode is set, the adjustment values of the
other modes are automatically set according to the mid-
dle speed mode setting in a certain relationship.
CAUTION: Since the high voltage output cannot be checked with a
digital multi meter in this model, a judgment of the out-
put must be made by checking the print image quality.
put must be made by checking the print image quality.
EXECUTE
EXECUTE
㩷
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'96(77,1*$1'287387
$˖
˷̚˹
˖0,''/(ǂ63(('ǂ'9%B.
$˖
˖0,''/(ǂ63(('ǂ'9%B&
%˖
˖0,''/(ǂ63(('ǂ'9%B0
&˖
˖0,''/(ǂ63(('ǂ'9%B<
'˖
2.
(;(&87(
/2:
0,''/(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'96(77,1*$1'287387
$˖
˷̚˹
˖0,''/(ǂ63(('ǂ'9%B.
$˖
˖0,''/(ǂ63(('ǂ'9%B&
%˖
˖0,''/(ǂ63(('ǂ'9%B0
&˖
˖0,''/(ǂ63(('ǂ'9%B<
'˖
2.
(;(&87(
/2:
0,''/(
10-key
or after 30 sec.
Item/Display (mode)
Content
Setting
range
Default
value
Actual voltage
62cpm
machine
70cpm
machine
MIDDLE
A
MIDDLE SPEED DVB_K
K developing bias set value at middle speed
0 - 600
450
–450V
5V
–450V
5V
B
MIDDLE SPEED DVB_C
C developing bias set value at middle speed
0 - 600
450
–450V
5V
–450V
5V
C
MIDDLE SPEED DVB_M
M developing bias set value at middle speed
0 - 600
450
–450V
5V
–450V
5V
D
MIDDLE SPEED DVB_Y
Y developing bias set value at middle speed
0 - 600
450
–450V
5V
–450V
5V
LOW
A
LOW1 SPEED DVB_K
K developing bias set value at low speed 1
0 - 600
450
–450V
5V
–450V
5V
B
LOW1 SPEED DVB_C
C developing bias set value at low speed 1
0 - 600
450
–450V
5V
–450V
5V
C
LOW1 SPEED DVB_M
M developing bias set value at low speed 1
0 - 600
450
–450V
5V
–450V
5V
D
LOW1 SPEED DVB_Y
Y developing bias set value at low speed 1
0 - 600
450
–450V
5V
–450V
5V
E
LOW2 SPEED DVB_K
K developing bias set value at low speed 2
0 - 600
450
–450V
5V
–450V
5V
F
LOW2 SPEED DVB_C
C developing bias set value at low speed 2
0 - 600
450
–450V
5V
–450V
5V
G
LOW2 SPEED DVB_M
M developing bias set value at low speed 2
0 - 600
450
–450V
5V
–450V
5V
H
LOW2 SPEED DVB_Y
Y developing bias set value at low speed 2
0 - 600
450
–450V
5V
–450V
5V
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man24) service manuals if exist.