MX-6201N, MX-7001N (serv.man18). ADJUSTMENTS SECTION - Sharp Copying Equipment Service Manual (repair manual). Page 15

Read Sharp MX-6201N / MX-7001N (serv.man18) Service Manual online

MX-7001N  ADJUSTMENTS  6 – 15
5)
Check that the inside dimension of the printed half tone is 240
± 0.5mm.
If the above condition is not satisfied, execute the procedures
below.
6)
Change the set value of set item A.
When the set value is changed by 1, the dimension is changed
by 0.1mm.
When the set value is increased, the BK image magnification
ratio in the main scanning direction is increased. When the set
value is decreased, the BK image magnification ratio in the
main scanning direction is decreased.
Repeat procedures 2) – 6) until a satisfactory result is obtained.
 
ADJ 11
Image off-center adjustment 
(Print engine section)
This adjustment must be executed in the following cases:
* When the LSU is replaced or removed.
* When “ADJ 10 Print engine image magnification ratio adjustment
(BK) (Main scanning direction) (Print engine section) (Manual
adjustment)” is performed.
* When a paper tray is replaced.
* When the paper tray section is disassembled.
* When the manual feed tray is replaced.
* When the manual feed tray is disassembled.
* When the duplex section is disassembled.
* When the duplex section is installed or replaced.
* When the large capacity paper feed tray is installed or replaced.
* When the large capacity paper feed tray section is disassembled.
* When the regist roller section is disassembled.
* When U2 trouble occurs.
* When the PCU PWB is replaced.
* When EEPROM on the PCU PWB is replaced.
(Caution)
Before execution of this adjustment, check the following item.
* Check to insure that the Print engine image magnification ratio
adjustment (BK) (Main scanning direction) (Print engine section)
(Manual adjustment) has been properly adjusted.
1)
Enter SIM50-10 mode.
2)
Select set item J with the scroll key and enter the value corre-
sponding to the paper feed tray to be adjusted.
Display/Item
Content
Set 
range
Default 
value
A
BK-MAG
Main scan print 
magnification ratio BK
60 – 140
100
B
MFT
Print off-center adjustment 
value (Manual feed tray)
1 – 99
50
C
CS1
Print off-center adjustment 
value (Paper feed tray 1)
1 – 99
50
D
CS2
Print off-center adjustment 
value (Paper feed tray 2)
1 – 99
50
E
CS3
Print off-center adjustment 
value (Paper feed tray 3)
1 – 99
50
F
CS4
Print off-center adjustment 
value (Paper feed tray 4)
1 – 99
50
G LCC
Print off-center adjustment 
value (LCC)
1 – 99
50
H
ADU
Print off-center adjustment 
value (ADU)
Note: Before execution of 
this adjustment, check to 
insure that the adjustment 
items A – G have been 
properly adjusted. If not, 
this adjustment cannot be 
made properly.
1 – 99
50
I
MULTI COUNT
Print quantity
1 – 999
1
A : 100
;
BK-MAG
B : 50
;
MFT
C : 50
;
CS1
D : 50
;
CS2
A:
SIMULATION NO.50-10
PAPER CENTER OFFSET SETUP
XXX
XXX
60
140
OK
TEST
CLOSE
E : 50
;
CS3
F : 50
;
CS4
G : 50
;
LCC
H : 50
;
ADU
I :
1
;
MULTICOUNT
J :
2
;
PAPER : CS1
K :
1
;
DUPLEX : NO
EXECUTE
A : 50
;
BK-MAG
B : 50
;
MFT
C : 50
;
CS1
D : 50
;
CS2
A:
SIMULATION NO.50-10
PAPER CENTER OFFSET SETUP
60
140
OK
TEST
CLOSE
E : 50
;
CS3
F : 50
;
CS4
G : 50
;
LCC
H : 50
;
ADU
I :
1
;
MULTICOUNT
J :
2
;
PAPER : CS1
K :
1
;
DUPLEX : NO
EXECUTE
End of print
EXECUTE
10-key
EXECUTE
Page of 76
Display

Click on the first or last page to see other MX-6201N / MX-7001N (serv.man18) service manuals if exist.