Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man21) Peripheral online
MX-FNX4 ADJUSTMENTS 8 – 3
11) Change the setting of bits from 6 to 8 of the SW504 depending
on the clearance. Refer to the table below.
* When the adjustment width is 0:
* When the adjustment width is 0:
Since the stitch position is aligned with the folding position,
the setting is not changed.
the setting is not changed.
* In the case of a "positive adjustment width":
Subtract the distance from the value on the above figure,
and set the obtained value to SW504.
Example) If the current set value of the SW504 is +2 and the
clearance is +1mm newly, set the SW504 to -2.
and set the obtained value to SW504.
Example) If the current set value of the SW504 is +2 and the
clearance is +1mm newly, set the SW504 to -2.
* In the case of a "negative adjustment value":
Add the distance to the value on the above figure, and set
the obtained value to SW504.
Example) When the current set value of the SW504 is -1 and
the distance is -0.5mm, newly set the SW504 to +1.
the obtained value to SW504.
Example) When the current set value of the SW504 is -1 and
the distance is -0.5mm, newly set the SW504 to +1.
The following bits must not be set.
12) Set bits from 1 to 4 of the SW504 to OFF.
(4) Stitch position (Center stapling adjustment)
(MX-FNX4)
Use the user mode of the host machine for this adjustment.
(5) Adjustment of stitcher unit (MX-FNX4)
1) Open the front cover.
2) Pull out the stitcher base unit to the front, and pull the stitcher
2) Pull out the stitcher base unit to the front, and pull the stitcher
handle [1] once and raise the stitcher.
3) Remove the three screws [2], and remove the stitcher cover
[3].
4)
Remove the positioning tool [4] attached to the back of the
cover.
cover.
5)
For adjustment of the stitcher in the front side, remove the front
guide plate [5] and the center guide plate [6]. For adjustment of
the stitch in the rear side, remove the center guide plate [6]
and the rear guide plate [7]. (one screw, each)
guide plate [5] and the center guide plate [6]. For adjustment of
the stitch in the rear side, remove the center guide plate [6]
and the rear guide plate [7]. (one screw, each)
6)
For adjustment of the stitcher in the front side, loosen the two
screws [9] of the stitcher base [8]. For adjusting of the stitcher
in the rear side, loosen the two screws [10] of the stitcher base
[8].
screws [9] of the stitcher base [8]. For adjusting of the stitcher
in the rear side, loosen the two screws [10] of the stitcher base
[8].
7)
Insert the tool [12] into the staple slot of the stitcher [11].
Bit setting of DIPSW1
Set value
(Unit:0.5 mm)
Bit 6
Bit 7
Bit 8
OFF
ON
ON
+3
OFF
ON
OFF
+2
OFF
OFF
ON
+1
OFF
OFF
OFF
0
ON
OFF
ON
-1
ON
ON
OFF
-2
ON
ON
ON
-3
Bit 6
Bit 7
Bit 8
ON
OFF
OFF
[2]
[3]
[1]
[4]
[7]
[6]
[5]
[10]
[9]
[8]
[11]
[12]
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man21) service manuals if exist.