MX-5500N, MX-6200N, MX-7000N (serv.man19). MX-FNX3 4 MX-RBX2 MXPNX2A-D SERVICE MANUAL-Disassembly Assembly-2 - Sharp Copying Equipment Peripheral (repair manual)

mx-5500n, mx-6200n, mx-7000n (serv.man19) peripheral
Model
MX-5500N MX-6200N MX-7000N (serv.man19)
Pages
30
Size
11.13 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-FNX3 4 MX-RBX2 MXPNX2A-D SERVICE MANUAL-Disassembly Assembly-2
File
mx-5500n-mx-6200n-mx-7000n-sm19.pdf
Date

Read Sharp MX-5500N / MX-6200N / MX-7000N (serv.man19) Peripheral online

MX-FNX4  DISASSEMBLY AND ASSEMBLY  6 – 40
(7) Delivery upper guide (MX-FNX4)
a. Removal of front cover
1) Open the front cover [1], and remove the clip [2].
2) Lift the front cover [1], and remove it. 
b. Removal of rear cover
1) Shift the tray cable cover [1] to the tray side, and remove it. 
2) Remove the six screws [2], and lift and remove the rear cover
[3].
c. Removal of saddle inlet front inside cover
1) Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
d. Removal of front inside upper cover
1)
Remove the four screws [1], and remove the front inside upper
cover [2]. 
e. Removal of left upper cover
1)
Remove the two screws [1].
2)
With the upper door [2] open, tilt the left upper cover [3] to the
right, and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
[1]
[2]
[2]
[1]
[3]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[3]
[2]
[1]
[4]
MX-FNX4  DISASSEMBLY AND ASSEMBLY  6 – 41
f. Removal of grate-shaped upper guide
1) Move down the tray [1] lower than the grate-shaped upper
guide [2]. (For moving of the tray, refer to " Removal of No.1
tray")
2) Remove the five screws [3], and remove the grate-shaped
upper guide [2].
g. Removal of No.1 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1) Remove the screw [1], and remove the metal plate [2] and the
slide guide [3]. If the grate-shaped upper guide has been
removed, this procedure is unnecessary.
2)
Remove the screw [4], and remove the stopper [5].
3)
Remove the two screws [6], and open the harness holder [7] at
three positions, and disconnect the connector [8] at two posi-
tions.
4)
Insert your finger into the hole in the back of the No. 1 tray [9].
Push the tray lift motor gear [10] toward you to release the
clutch, and lift the No. 1 tray [9].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
[3]
[2]
[1]
[2]
[1]
[1]
[3]
[2]
[5]
[4]
[7]
[8]
[6]
[6]
[9]
[10]
MX-FNX4  DISASSEMBLY AND ASSEMBLY  6 – 42
h. Removal of No. 2 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1) Remove the screw [1], and remove the stopper [2].
2) Remove the two screws [3], and disconnect the connector [4].
3)
Insert your finger into the hole in the back of the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray from the bottom in advance so as not
to twist the tray cable.
i. Removal of grate-shaped lower guide
1)
Remove the ten screws [1], and remove the grate-shaped
lower guide [2].
CAUTION: When installing, be careful not to damage the grate-
shaped lower guide by hanging it to the sensor flag arm
on the delivery side.
j. Removal of delivery upper guide
1)
Remove the two screws [1] and the earth wire [2], and remove
the delivery upper guide [3].
[2]
[1]
[2]
[1]
[4]
[3]
[3]
[5]
[6]
[1]
[1]
[1]
[2]
[1]
[2]
[1]
[3]
MX-FNX4  DISASSEMBLY AND ASSEMBLY  6 – 43
(8) Inlet feed unit
a. Removal of front cover
1) Open the front cover [1], and remove the clip [2].
2) Lift the front cover [1], and remove it.
* For MX-FNX3, refer to 1-A-(1)-a.
b. Removal of rear cover
1) Slide the tray cable cover [1] to the tray side, and remove it. 
2) Remove six screws [2], and lift and remove the rear cover [3].
* For MX-FNX3, refer to 1-A-(2)-a.
c. Removal of saddle inlet front inside cover
1) Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
d. Removal of front inside upper cover
1)
Remove the four screws [1], and remove the front inside upper
cover [2].
* For MX-FNX3, refer to 1-A-(3)-d.
e. Removal of inlet feed unit
1)
Disconnect the connectors [1] at four positions, and remove
the harness from the clamp [2].
2)
Remove the four screws [3].
3)
Open the upper cover [4], and remove the inlet port feed unit
[5].
[1]
[2]
[2]
[1]
[3]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
[1]
[1]
[2]
[3]
[3]
[5]
[4]
Page of 30
Display

Download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man19) Peripheral

Here you can read online and download Sharp MX-5500N / MX-6200N / MX-7000N (serv.man19) Peripheral in PDF. MX-5500N / MX-6200N / MX-7000N (serv.man19) peripheral will guide through the process and help you recover, restore, fix, disassemble and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man19) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.