Read Sharp MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man2) Handy Guide online
REPAIR HINTS
SHARP
78
TROUBLE CODES
MX-5070N
MX-6070N
MX-6070N
C1-01/03/05/07 trouble during MC
cleaning
Update the MFP Firmware to 05.11.Z1.00 (or higher)
ALL
E7-03, E7-90 trouble and/or Indication
of Toner Quantity [0%] during MFP
startup.
MX-5070N
MX-6070N
MX-6070N
F2-65 trouble during continuous run
operation
ALL
Intermittent F1-00 trouble
Update the PCU Firmware to 05.00.Z1.00 and MXFN27
Inner Firmware to 01.03.Z1.a0 (or higher).
MX-FN27
Intermittent F1-04 or F1-22 Errors
This may be due to the Paddle Drive Clutch not reversing
to allow the paddles to return to their home position.
Replace the following parts (MXFN27 PG Section 3):-
0CWFE360460// (Item 7 - Clutch) x 2.
0CWFU207660// (Item 13 - Gear) x 2.
0CWFU207660// (Item 13 - Gear) x 2.
0CWFU207670// (Item 14 - Pulley) x 1.
Note: There are two clutches that need to be replaced
(Item 7 & 13), but only 1 Pulley is required (Item 14).
ALL
Intermittent H4-00, only when the
Motion Sensor is enabled
Upgrade the PCU firmware to 04.00.Z1.00 (or higher).
ALL
L4-11
The MX-TU16 Centre Exit Tray Unit is supplied with a
drive assembly that must be installed to enable the offset
shifter to operate. Without the Centre Exit Tray Unit,
L4-11 trouble will be displayed if no finishing option is
installed (MX-FN27 or MX-FN29/31 with MXRB25).
As a temporary measure, changing SIM55-01, SW24-7
from 0 to 1 will allow machine operation without an
option finisher however, this soft switch MUST be set
back to 0 (default) once the Finisher is reinstalled.
IMAGE SEND
ALL
Using Blank Page Skip function, is it
possible to disable the number of
pages sent confirmation message?
It is not possible to disable the confirmation message.
However, to prevent the cancellation of a scan job if OK is
not pressed from the confirmation message, change the
following SW setting:-
SIM66-1, SSW 95, Data 7 from 0 to 1
MX-FX15
When unpacking the MX-FX15
Fax Expansion Kit, there is no line cord
included?
The line cord is no longer supplied with the MX-FX15.
Use the line cord from the existing machine, or the
MX-FX13 line cord may be ordered and used.
Note: Line cords are supplied for UK, German & French
markets only.
ALL
How to setup scan to Office 365 email
from the Sharp MFP?
Check the following settings under System Settings ->
Network Settings -> Service Settings -> SMTP:-
Primary Server: smtp.office365.com
Port Number: 587
Sender Address: ****@onmicrosoft.com
SSL: ON
SMTP Authentication: ON
Click on the first or last page to see other MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man2) service manuals if exist.