Read Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man13) Service Manual online
MX-4101N ADJUSTMENTS 5 – 98
ADJ 23
Document size sensor
adjustment
adjustment
This adjustment is needed in the following situations:
* When the original size sensor section has been disassembled.
* When the original size sensor section has been replaced.
* When U2 trouble has occurred.
* When the scanner control PWB is replaced.
* When the EEPROM on the scanner control PWB is replaced.
* When the original size sensor section has been disassembled.
* When the original size sensor section has been replaced.
* When U2 trouble has occurred.
* When the scanner control PWB is replaced.
* When the EEPROM on the scanner control PWB is replaced.
23-A
Document size sensor detection point
adjustment
adjustment
1)
Go through the modes specified in Simulation 41-1.
Loosen the original cover switch actuator adjustment screw
and slide the actuator position so that the display OCSW is
returned to the normal display when the height of the arm unit
top from the table glass is 32
and slide the actuator position so that the display OCSW is
returned to the normal display when the height of the arm unit
top from the table glass is 32
±0.5mm by slowly tilting the doc-
ument detection arm unit in the arrow direction and adjust.
(If the ON timing of the original cover switch is shifted, the doc-
ument detection function may malfunction.)
(If the ON timing of the original cover switch is shifted, the doc-
ument detection function may malfunction.)
23-B
Adjust the sensitivity of the original size
sensor
sensor
1)
Enter the SIM41-2 mode.
2)
Execute the sensor adjustment without document.
With the document cover open, without placing a document on
the table glass, press [EXECUTE] key.
With the document cover open, without placing a document on
the table glass, press [EXECUTE] key.
3)
Place A3 (11" x 17") paper on the document table and press
[EXECUTE] key.
If the adjustment is completed normally, "DOCUMENT PHOTO
SENSOR LEVEL IS ADJUESTED" is displayed.
[EXECUTE] key.
If the adjustment is completed normally, "DOCUMENT PHOTO
SENSOR LEVEL IS ADJUESTED" is displayed.
ADJ 24
Manual paper feed tray paper
size (width) sensor adjustment
size (width) sensor adjustment
This adjustment is needed in the following situations:
* The manual paper feed tray section has been disassembled.
* The manual paper feed tray unit has been replaced.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
* The manual paper feed tray section has been disassembled.
* The manual paper feed tray unit has been replaced.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
3'6(1625&+(&.
2&6:
3'
3'
3'
3'
3'
3'
3'
32 0.5mm
+
-
Adjustment completed
EXECUTE
Adjustment
failed
failed
EXECUTE
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'2&80(176,=(3+2726(16256(783
(;(&87(
ේⓂᬌ⍮ࡦ ࠨߩࡌ࡞ࠍ⺞ᢛߒ߹ߒߚޕ
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'2&80(176,=(3+2726(16256(783
(;(&87(
ࠝࠫ࠽ ࡞ࠞࡃࠍ㐿ߚ⁁ᘒߢࠟࠬ㕙ߦේⓂࠍ࠶࠻ߒߥߢ
=':'%76'?ࡏ࠲ࡦࠍߒߡߊߛߐޕ
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'2&80(176,=(3+2726(16256(783
(;(&87(
ࠟࠬ㕙 ߦ#
ࠨࠗ࠭ߩ↪⚕ࠍ࠶࠻ߒߡޔ
=':'%76'?ࡏ࠲ࡦࠍߒߡߊߛߐޕ
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
'2&80(176,=(3+2726(16256(783
(;(&87(
ਅ⸥ߩේⓂ ᬌ⍮ࡦࠨߢ⺞ᢛਇ⦟߇⊒↢ߒ߹ߒߚޕ
2&
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man13) service manuals if exist.