MX-3500N, MX-3501N, MX-4500N, MX-4501N (serv.man99). 064-TO OVERCOME VOID AREAS IN K DEVELOPER (VER 2) - Sharp Copying Equipment Technical Bulletin (repair manual)

mx-3500n, mx-3501n, mx-4500n, mx-4501n (serv.man99) technical bulletin
Model
MX-3500N MX-3501N MX-4500N MX-4501N (serv.man99)
Pages
3 Few pages! See other manuals at the bottom of the first or last page.
Size
116.04 KB
Type
PDF
Document
Technical Bulletin
Brand
Device
Copying Equipment / 064-TO OVERCOME VOID AREAS IN K DEVELOPER (VER 2)
File
mx-3500n-mx-3501n-mx-4500n-mx-4501n-sm99.pdf
Date

Read Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man99) Technical Bulletin online

 
 
 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1. Model Name 
 
MX3500N – MX4500N - MX3501N – MX4501N 
 
2. Symptom 
On very rare occasions during a long run with high density images, a feint band will 
appear in the black part of the image. 
 
3. Cause 
The toner in the black developer tank will clog behind the mag roller and will stop the 
developer brush from forming, this will create a void area on the mag roller and hence 
limited or no toner will be transferred. 
 
4. Repair 
The procedure to overcome this is to fit a mylar stirring sheet to the rear developer mixing 
auger. 
 
5. Parts Required  
 
Part Name 
Part Number 
DMX Roller L 
NROLP1515FCZ2 
Paper Dust Churning Sheet 
PSHEZ5564FCZ1 
 
6. Procedure 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
To overcome void areas in K Developer 
SUK TECHNICAL BULLETIN 
Date:  
9
th
 November 2007 
Model:  
MX3500N – MX4500N 
 
 
MX3501N – MX4501N 
Ref.:   
064 
Colour:  
White 
Page:  
1 of 3 
 
 
Remove both upper and lower cover by removing 5 screws 
 
Remove end cover by removing 1 
screw 
 
 
 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Remove e-clip and bearing housing 
 
Remove three red screws, and then 
remove cover. 
NOTE. Do NOT remove red screw that 
adjusts developer tank position 
 
 
 
Remove 2 auger drive gears 
 
Now remove cover and bearings and 
remove rear auger shaft from developer 
module 
If the developer tank is new and unused then you can use the Mixing auger that was 
removed, if not then use the new auger. 
Starting at the gear end, begin sticking the mylar churning sheet to the shaft so that the 
stirring fingers stick out beyond the auger. When reaching the small piece of plastic that 
cleans the toner concentration sensor stop, and cut the mylar. Restart again after the 
sensor cleaner. Continue to the end of the shaft. When reaching the end of the shaft the 
mylar will be too long, trim the excess. It should look like the picture below. 
Now refit the auger into the developer module in the reverse order in which it was 
removed, so that it now looks like the image below 
 
 
 
Sharp Electronics (UK) Ltd., Technical Services Group
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Ensure that the DMX rollers are aligned as shown in the diagram below 
 
 
 
 
Refill with developer, refit into machine and if new developer was used perform SIM25-02 
for black only, if the old developer was used perform SIM25-01 
 
 
Page of 3
Display

Download Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man99) Technical Bulletin

Here you can read online and download Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man99) Technical Bulletin in PDF. MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man99) technical bulletin will guide through the process and help you recover, restore, fix, disassemble and repair Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man99) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.