Read Sharp MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man5) Handy Guide online
Simulation Codes
33
Document Solutions After Sales Service
24
Data Counter Clear
1
Jam/trouble counter clear
2
Paper feed counter clear
3
Document feed & output counter clear
24
Data Counter Clear cont…..
4
Maintenance counter clear
5
Developer counter clear
6
Copy Counter clear
9
Print & other counter clear
10
Fax counter clear
15
Network scanner counter clear
25
Usage Estimator data display
35
Toner Cartridge Use Status data clear
25
DV Auto Adjustment / Monitor
1
Toner sensor output monitor (Process drive)
2
Auto developer adjustment setting
4
Operation data of toner supply quantity
5
Display toner correction data
26
Device Configuration
1
Right Tray setup
2
LCC setup
3
Auditor setup
5
A3 Total/Maintenance counter setup
6
Destination setup
7
Machine ID setup
10
Network scanner trial mode setup
18
Toner save operation
30
CE mark control setup
32
Specifications for fusing cleaning operation
35
Trouble memory mode setting
38
Engine life over setting (Developer)
41
Pamphlet mode AMS operation
49
Copy speed mode setup (Postcard)
50
Function setting (B/W reverse, colour mode,
finisher)
finisher)
51
Specifications for Serial Port operation (For PCI)
52
Blank paper count mode setting
53
Enable/Disable auto colour calibration
65
Finisher alarm set-up (stapled sheets)
69
Toner near end setting
71
Web browsing trial mode setup
73
Poster enlargement image loss adjustment
74
OSA trial mode set-up
78
Remote panel operation password setting
79
Enable/Disable user data delete result
30
Sensor Operation / Test
1
Main unit sensor check
2
Tray sensor check (main)
40
Bypass Operation / Adjustment
2
Bypass tray width adjustment
7
Bypass tray width detection manual setting
41
OSS Operation / Adjustment
1
Document sensor operation check
2
Document sensor output setup
3
Document sensor output display
43
Fuser Setting
1
Fuser temperature setup (Paper)
4
Fuser temperature. setup for each mode
20
Fuser temperature. correction for low
temperature & humidity
temperature & humidity
21
Fuser temp correction for high temperature &
humidity
humidity
22
Perform L/L correction for fuser temperature
setting
setting
23
Perform H/H correction for fuser temperature
setting
setting
24
Fuser temperature reset
31
Check operation of web cleaning (36 only)
32
Force web cleaning at job end (36 only)
44
Process Control
1
Process control mode setting
2
Process control Gain Adjustment
4
Process control initial density setup
6
Process control correction (force)
9
Process control data display
12
DM data, patch/base data display
13
Image density set-up (colour)
14
Fuser temp.& humidity output data
15
OPC drum idle rotation
21
Half tone process control registration
22
Half tone process control density patch result
24
Half tone correction data result display
25
Initial half tone correction data display
26
Half tone process control correction execution
27
Half tone process control correction data clear
28
Process control timing (On/Off) setting
29
Enable/disable half tone correction during each
job
job
31
OPC drum position adjustment
37
Image density correction setting
43
DV unit installation monitor
61
Set Calibration data of colour image density
sensor
sensor
62
Process control execution conditions
Click on the first or last page to see other MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man5) service manuals if exist.