Read Sharp MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man117) Technical Bulletin online
Sharp Electronics (UK) Ltd., Document Systems Support
2/3
[Description]
No.
Item
Details
1
Specification
Support for Scan accessory kit MX-AP14
2
Main unit control
Modification of U7 trouble due to excess amount of time required for activation process to
register vast amount of job log
register vast amount of job log
3
Main unit control
Modification of L8-20 which may occur when condition signaling between internal
modules is not done properly.
modules is not done properly.
4
Main unit control
Modification of a problem which occurs with following steps: 1) Print out a test pattern in
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
5
Main unit control
Modification of machine lock up and paper jam at SPF (ICU_REQ) etc.
These problems may occur when internal module cannot communicate while load is
applied on CPU.
These problems may occur when internal module cannot communicate while load is
applied on CPU.
6
Main unit control
Modification of a failure to complete Fax firmware upgrade during firmware upgrade
7
Main unit control
Enhancement of output from high-voltage PWB to secondary transfer to remedy C4-00
error under low temperature environment.
error under low temperature environment.
8
Main unit control
Laser power adjustment control according to the gradation of each machine-specific has
been added to improve the color stability of the halftone density.
*Note:
Color balance adjustment needs to be executed after changing the following Soft SW to
enable this setting when updating the firmware in the field.
If the set value has already been changed individually for the support of image quality
before the firmware update, please return the value to the default once, and then execute
the color balance adjustment.
[Monochrome laser power adjustment]
SIM55-1 SW No.9 Data No.3
0: OFF
1: ON (Default)
[Color laser power adjustment]
SIM55-1 SW No.24 Data No.2
0: OFF
1: ON (Default)
been added to improve the color stability of the halftone density.
*Note:
Color balance adjustment needs to be executed after changing the following Soft SW to
enable this setting when updating the firmware in the field.
If the set value has already been changed individually for the support of image quality
before the firmware update, please return the value to the default once, and then execute
the color balance adjustment.
[Monochrome laser power adjustment]
SIM55-1 SW No.9 Data No.3
0: OFF
1: ON (Default)
[Color laser power adjustment]
SIM55-1 SW No.24 Data No.2
0: OFF
1: ON (Default)
9
UI
Modification to allow enable/disable "Default Verification Stamp" setting in each mode
separately. (Now it is allowed to set for Fax/I-Fax mode and other modes.)
separately. (Now it is allowed to set for Fax/I-Fax mode and other modes.)
10 Printer
Modification of machine lock up which occurs while spooling particular data including
JPEG image
JPEG image
11
Printer
Modification of a failure to print out particular Excel data which includes TIFF image
12 Printer
Modification of overlapped characters which may appear when data are printed directly
from USB flash drive.
from USB flash drive.
13 Printer
Modification of garbled characters which may appear during the direct print of PDF file
14 Printer
Modification of a failure to print out particular PDF data directly from USB flash drive
15 Printer
Modification of termination of printing particular PDF file without printing entire file. Even
when the data are printed, the print process takes too long.
when the data are printed, the print process takes too long.
16 Printer
Modification of a failure to process large amount of data with raster pattern. The unit
displays "Rendering" and never output the data.
displays "Rendering" and never output the data.
17 Printer
Modification of machine lock up which occurs while printing particular or large volume PS
file.
file.
18 Printer
Modification of occasional image rotation of page 2.
It rotates by 90 degrees while printing a PS file.
It rotates by 90 degrees while printing a PS file.
19 Printer
Modification of problems with Network printing, such as 1) paper jam which is not logged
in Jam History, 2) machine lockup rejecting key operations
in Jam History, 2) machine lockup rejecting key operations
20 Printer
Modification of machine lockup which occurs after completing a batch print of several PS
files (which includes the data in duplex printing)
files (which includes the data in duplex printing)
Click on the first or last page to see other MX-2640N / MX-2640NR / MX-2640FN / MX-3140N / MX-3140NR / MX-3140FN / MX-3640N / MX-3640NR / MX-3640FN (serv.man117) service manuals if exist.